Induced Drag and Parasite Drag: The Operational Use of the Best Glide Point

Silhouette d'aile de planeur sur ciel pâle

Engine failure in cruise at FL370: the procedure calls for a speed markedly lower than the cruise Mach, the aircraft settles into a slow descent toward a level it will hold on one engine, and the question comes up in the debrief — why that speed, and not the one that gave the best fuel mileage ten minutes earlier? The answer lies neither with the engine nor with the computer, but with the shape of the drag curve and the single point where its two contributions balance. That point governs the drift-down, the glide, the hold, and the climb gradient in a degraded configuration — four situations with nothing in common except this one point.

Two drags, two opposing laws, and their sumDrag as a function of speed. Parasite drag grows as the square of speed; induced drag falls as its inverse square. Their sum passes through a minimum, reached exactly where the two terms are equal. This point is not a comfort setting: it is where the aircraft covers the greatest distance for a given amount of energy.dragspeedinducedparasiteminimum totalthe two terms are equal there
The best-glide point is derived, not adjusted. It is fixed by the wing geometry and the weight at the time. No lever moves it: one only chooses whether or not to fly it.

The best-glide point is where the two types of drag (parasite and induced) are equal. This is the speed that lets an aircraft glide the farthest with the least energy. It changes with weight but not with wind or other factors.

An Airbus A320 at 120,000 lbs and FL370 has a best-glide speed of 230 knots. If the weight drops to 100,000 lbs, the best-glide speed decreases to 210 knots. The glide distance remains the same, but the aircraft descends faster at the higher weight.

Two drags, two opposing growth laws

Parasite drag gathers everything the aircraft pays to move through the air: skin friction over the wetted surface, form drag, interference at junctions, protuberances. It ignores lift and weight. With configuration fixed, it follows dynamic pressure: doubling the speed multiplies it by four.

Induced drag is the price of lift. A wing of finite aspect ratio cannot deflect air downward without generating a trailing-edge vortex system; this deflection tilts the local flow, and the resulting force acquires a rearward component. Its magnitude varies as the square of the lift coefficient, divided by the effective aspect ratio. Since lift balances weight, the lower the speed, the higher the required lift coefficient — and the more induced drag explodes.

The sum traces a bowl shape: the induced term dominates at low speeds, the parasite term takes over at high speeds, and a minimum exists between the two.

The two contributions: behavior and levers
Criterion Parasite drag Induced drag
Origin Friction, form, interference, protuberances Trailing-edge vortices, finite aspect ratio wing
Effect of speed Grows as dynamic pressure Falls as the inverse of dynamic pressure
Effect of weight None Grows as the square of weight
Dominance High speeds: cruise, rapid descent Low speeds: holding, glide, climb
Operational lever Aerodynamic cleanliness, clean configuration Weight, altitude, load factor

The best-glide point: where the two terms are equal

On an idealized parabolic drag polar, the sum reaches its minimum exactly where the two terms are equal. This is no coincidence: one grows as the square of speed, the other falls as its inverse, and the derivative of the sum vanishes only at equality. One sentence is then enough to reason about the whole subject — at the best-glide point, half the drag is parasite, the other half induced.

A white turboprop aircraft in flight with landing gear down, emitting wing vapor trails.
Landing gear increases drag, reducing glide efficiency.

Best glide ratio, minimum drag, minimum required thrust, shallowest glide angle: four names for the same flight condition. The best glide ratio is a property of the airframe in a given configuration, and it does not move with weight. What moves is the speed that delivers it, which varies as the square root of the ratio of weight to air density. Expressed as indicated airspeed, it therefore depends almost solely on weight — hence the usual display by weight bracket, as long as compressibility stays out of play. In clean configuration, the best glide ratio of a transport aircraft is typically in the high teens.

The bowl is flat, but its two sides are not equal

The neighborhood of the minimum is remarkably flat: the penalty depends only on the ratio between the speed flown and the best-glide speed, and a ten percent deviation costs only a few percent of drag, hence of glide distance.

The symmetry stops at arithmetic. On the fast side, a deviation costs only drag. On the slow side, it crosses into the back side of the power curve: below minimum-drag speed, slowing down demands more thrust. A speed loss is no longer self-correcting there, the margin to buffet closes, and recovery costs altitude.

Cost of a deviation, idealized parabolic polar
Fraction of best-glide speed Relative drag, order of magnitude Glide ratio retained Operational signature
0.80 +10 percent 91 percent Marked back-side regime, buffet margin eroded
0.90 +2 percent 98 percent No cost, but already in the back side: speed not self-stable
1.00 reference 100 percent Minimum drag
1.10 +2 percent 98 percent Negligible, speed stable
1.20 +7 percent 94 percent Parasite term dominant

The trap. Correcting downward when in doubt about the best-glide speed: the reflex looks cautious, but it is structurally wrong. A value established for a heavy weight, flown at a light weight, places you on the fast side and costs a few percent. The reverse error settles you into the back side: required thrust rises, buffet margin shrinks, and the gesture meant to help the situation makes it worse. With an engine out, this is paid not in glide ratio but in lost drift-down level.

The right reflex. Recalculate the speed for the actual weight, then deliberately fly a few knots above it. The bowl is flat: the extra cost is one to two percent, negligible against the uncertainty of the real drag polar, and it buys speed stability and buffet margin. Same logic when gliding: add speed into a headwind, shave a little off with a tailwind.

What this point governs, and what it does not

Treating the best glide ratio as a universal optimum is the most common confusion: it is one only for objectives expressed in terms of force. As soon as they are expressed in terms of power or hourly fuel flow, the optimum shifts.

It governs the maximum glide distance, the minimum required thrust, the endurance of a jet aircraft, and its maximum climb angle — hence the most favorable gradient after a thrust loss. It also governs the range of a propeller aircraft, whose fuel consumption follows power.

It does not govern minimum sink rate, which corresponds to minimum required power and is obtained more slowly: the model places that point at roughly three-quarters of the best-glide speed. Nor does it govern the range of a jet aircraft, which seeks the maximum of speed times glide ratio, is obtained on the order of a third faster, and retains not quite nine-tenths of the glide ratio there. Hence the gap between cruise Mach and drift-down speed.

Decision matrix: position relative to best glide ratio
Objective Quantity optimized Jet aircraft Propeller aircraft
Maximum glide distance Glide ratio Best glide ratio Best glide ratio
Maximum glide flight time Required power Noticeably below Noticeably below
Maximum endurance, holding Hourly fuel flow Best glide ratio Below, minimum power
Maximum range Distance per unit of fuel About a third faster Best glide ratio
Maximum climb angle Thrust excess Best glide ratio Below
Glide: weight changes the speed, not the angleTwo glides from the same altitude, at different weights. The slope is identical: it depends only on the glide ratio, hence on aerodynamics. The speed at which one must fly to achieve it, however, grows with weight. The heavy aircraft reaches the same point, faster and sooner.light: slowerheavy: fasteridentical slopesame arrival point, reached sooner
Range does not depend on weight. Counterintuitively, the heavy aircraft glides just as far — it simply descends faster along the same slope. What changes is the time available to decide.

The glide: what weight changes, and what it does not

In stabilized descent without thrust and at shallow angles, the glide ratio equates to the glide ratio itself. Since best glide ratio does not depend on weight, glide range does not depend on it either: two aircraft of different weights, each at its own best-glide speed, touch down at the same point — the heavy one faster and with a steeper sink rate. Weight buys speed and sink rate, not distance.

Hence a useful rule of thumb: a glide ratio in the high teens applied to the vertical distance represented by a high cruise level places the glide range at around a hundred nautical miles in still air — enough to distinguish a viable diversion field from one that is out of reach.

Configuration acts twice, in a way that surprises. Extending the gear or speed brakes increases the parasite term, and the best glide ratio drops. But the speed that delivers it drops too, because the equality of the two terms shifts toward a higher lift coefficient. A dirty aircraft therefore glides best more slowly than a clean one, and keeping the clean-configuration speed after extending everything stacks both penalties. Wind, for its part, does not change the glide ratio but changes the objective: maximizing ground distance means accelerating into a headwind, to reduce exposure time.

Holding, drift-down, and the second-segment exception

On a jet aircraft, hourly fuel consumption tracks thrust produced closely: at a given altitude, flying at minimum drag burns the least fuel per unit time, and holding speed derives directly from the best-glide point. Published speeds always drift from it slightly — maneuvering margin, buffet margin at altitude, maximum holding speeds imposed by air traffic procedures. The flat bowl makes these compromises cheap.

Drift-down is the case where the mechanism becomes binding again: with an engine out, available thrust collapses while drag remains what it is. The gradient is written as the ratio of thrust excess to weight; since jet engine thrust varies little with speed, that excess is maximal where drag is minimal. Drift-down speed is therefore not arbitrary: it is the best-glide speed at the current weight — the one that gives the highest stabilization level, a level on which en-route terrain clearance depends, assessed on a net flight path, that is, a gross gradient penalized by a fixed margin.

One exception deserves to be known: the takeoff climb segment with an engine out. Best glide ratio there would be achieved at a speed and configuration that certification forbids — stall margin, lateral controllability, flap setting. Takeoff safety speed is not an aerodynamic optimum but a constrained compromise, and knowing where the optimum gives way to certification is worth more than knowing the optimum itself.

High altitude: the two-drag model stops being enoughDrag as a function of Mach number in high-altitude cruise. Beyond the critical Mach, wave drag adds itself to the parasite and induced terms and rises very steeply. The minimum of the sum shifts and narrows: the range of economical speeds becomes tight, and the pure glide-ratio optimum is no longer the operational optimum.dragMach numbertwo-term modelwave drageconomical range narrowed
In high cruise, glide ratio no longer has the last word. The wave term imposes a limit that the textbook model ignores. This is why the cruise speed adopted by the operator is almost never the best-glide speed.

High altitude: when the model stops answering

Everything above rests on an unstated assumption: the drag polar does not depend on Mach number. At altitude, that assumption fails. Beyond the drag-divergence Mach a third term appears, wave drag, which grows sharply with Mach and is worsened by a high lift coefficient. The bowl acquires a wall on its right side, and that wall moves closer as altitude increases.

On the left side, the constraint is symmetric: the lift coefficient required at best-glide speed moves closer to the one that triggers low-speed buffet. The usable band closes between buffet and Mach limit, and the aerodynamic optimum can fall outside the operable envelope — hence manufacturer tables rather than a formula.

The second trap. Carrying the clean-polar reasoning over to a high cruise level. At heavy weight, at the highest cruise levels in the envelope, the indicated best-glide speed can correspond to a Mach where wave drag is already active, with the associated lift coefficient encroaching on the buffet margin. The theoretical optimum then lies exactly where the aircraft has no margin left: one descends first, and it is the manufacturer’s tabulated setting that gives the answer.

What to go check in one’s own documentation

Three questions deserve a written answer before the need arises. Under what assumptions is the flight manual’s glide polar established: engines windmilling or shut down, gear and flaps retracted. At what weight is the published best-glide speed referenced, and by what law does it correct for weight and altitude — a value recalled from memory is valid at one weight only. Finally, what does the computer produce with an engine out: a recalculated minimum-drag speed, or a fixed setting drawn from a table?

The gray zone will not close. A real drag polar is not parabolic: the zero-lift drag coefficient varies with Mach, span efficiency depends on in-flight wing deformation, and trim drag depends on center of gravity — an aft center of gravity within limits reduces the load on the tailplane, and hence its associated drag. The equality of the two terms is a modeling result: it gives reliable trends, never a figure to carry into a performance calculation.

The lesson is one of method for anyone preparing a type rating: the discriminating questions concern a direction of variation, almost never a value. Heavier, speed goes up and glide ratio does not move; gear down, both go down; headwind, accelerate; engine out, seek minimum drag rather than best fuel mileage. Knowing in addition which of these statements is an aerodynamic optimum and which is a certification compromise means having understood the subject — the technical preparation courses revolve around these chains of reasoning more than around formulas.

In case of discrepancy, the applicable regulatory text, the type’s approved flight manual, and the approved operating documentation take precedence over this article, whose sole purpose is to explain the mechanism.

Questions fréquentes

Why is drift-down speed so far from cruise Mach?

Because the two speeds answer different questions. Cruise Mach maximizes distance covered per unit of fuel, which on a jet aircraft lies noticeably above minimum-drag speed. Drift-down, by contrast, seeks the least unfavorable gradient, hence the maximum thrust excess, obtained where drag is minimal — that is, at the best-glide point, at the current weight.

Does weight change the glide range?

No, provided one flies the best-glide speed corresponding to the actual weight. Best glide ratio is a property of the airframe in a given configuration and does not depend on loading: the glide ratio is identical. What weight changes is the speed that delivers this ratio, which varies as the square root of weight, and consequently the sink rate. A heavy aircraft therefore reaches the same point, faster and in less time.

Why does the best glide speed decrease when the gear is extended?

Extending the gear increases parasite drag without touching the induced term. Since the optimum lies where the two terms are equal, a stronger parasite term shifts that equality toward a higher lift coefficient, hence toward a lower speed. Best glide ratio decreases and the speed that delivers it decreases too: keeping the clean-configuration speed after extending everything stacks both penalties.

In case of doubt about best-glide speed, should one fly a little faster or a little slower?

A little faster. The drag curve is very flat near its minimum: a few knots in excess cost only one or two percent of drag. On the slow side, by contrast, one enters the back side of the power curve, where slowing down demands more thrust, where the buffet margin closes, and where a speed loss no longer corrects itself. The arithmetic cost is comparable, but the operational consequence is not.

Does the published holding speed correspond exactly to best glide ratio?

It draws on it without being identical to it. For a jet aircraft, minimum hourly fuel flow does indeed occur at the minimum-drag point, which is the basis of holding logic. The published value then incorporates a maneuvering margin, a buffet margin at altitude, the chosen configuration, and the maximum holding speeds imposed by air traffic procedures. The flatness of the drag curve makes these deviations cheap in fuel.

Does the best-glide-ratio reasoning still hold at cruise level?

Not as is, because it assumes a drag polar independent of Mach number. At altitude, wave drag adds a third term that closes the curve on the fast side, while the required lift coefficient moves closer to low-speed buffet on the slow side. The theoretical optimum can then fall outside the actually usable band, which is why manufacturers publish tables with an altitude correction rather than a single rule.

Commentaires

Leave a Reply

Découvrez l’écosystème FL330

FL330, c’est toute l’aviation professionnelle — explorez nos autres espaces.