Extended Diversion Time Operations: What Belongs to the Type, and What Belongs to the Operator

A pilot in a dimly lit cockpit reviews extended diversion time calculations on a flight management system during an overcast dusk flight.

The flight manual states one hundred and eighty minutes. The network is preparing a route that requires only one hundred and forty. And the file stays stuck for months — not because of the aircraft, but because of the maintenance programme, the list of en-route alternate aerodromes and the critical fuel calculation. The number carried by the design and the one carried by the operating approval are written in the same unit without designating the same thing; confusing them costs an entry-into-service schedule.

Two approvals that carry the same number

The extended diversion time operations regime rests on two durations that must be kept separate. The threshold is the flight time, measured at one-engine-inoperative cruise speed, beyond which the aircraft moves too far from an adequate aerodrome to remain within the standard regime. The maximum diversion time is the duration, measured in the same way, that an airframe-engine combination has demonstrated it can sustain and that an operator has been approved to plan for.

The first is a boundary of applicability: crossing the threshold makes nothing irregular, it simply brings the flight into a regime where more must have been demonstrated. The second is a ceiling. For a twin-engine transport aircraft, the threshold that has long been retained is on the order of one hour. Aircraft with more than two engines are not out of scope for all that: a threshold is also set for them, higher, because the loss of one engine there leaves a propulsion margin of a wholly different order.

Where the vocabulary traps the practitioner is that the same value — one hundred and twenty, one hundred and eighty, more — is used for three distinct things. The first is a design capability: it attaches to a specific airframe-engine combination, it is demonstrated before the certification authority and it is recorded in the approved flight manual or its supplement. The second is an operating approval: it attaches to a named operator, for a named area of operation, and it can never exceed the design capability but may well remain below it. The third is the value actually usable on the morning of departure, once the state of the aircraft, that of the aerodromes and the fuel carried have been taken into account.

A capable aircraft therefore never suffices to authorise a route. It sets the ceiling under which the operator will have to build, and that ceiling is almost never the limiting factor in the schedule.

What the design demonstrates, and what it bounds

On the type side, the demonstration rests on two families of argument that have nothing to do with each other: propulsion reliability, which is a matter of fleet statistics, and system endurance capability, which is a matter of physical duration.

Propulsion reliability is measured across a fleet

The object approved is not the airframe but the airframe-engine combination. Changing engine variant, or even control-computer standard, reopens the file. The central indicator is the in-flight shutdown rate per operating hour, tracked across the entire worldwide fleet of the type: the longer the diversion time requested, the lower the required rate, and this requirement does not relax after approval. It is monitored continuously, which makes the type’s capability a state, not an acquisition.

To this is added what sustained single-engine operation demands of the machine: thrust maintained over a long period, thermal balances, oil reserve, fuel feed with unbalanced tanks, in-flight relight envelope. This demonstration formerly required accumulated operating hours; the so-called early entry path allows it to be obtained through design and testing from entry into service, at the cost of closer monitoring that falls in part to the first operators.

The most limiting system sets the ceiling

The second family of arguments is more prosaic. A three-hour diversion assumes that everything on which flight safety depends will hold for three hours, plus a margin. The significant systems are therefore listed — those whose failure or degradation would jeopardise continuation of the flight and landing at the diversion aerodrome — and an endurance duration is established for each. Electrical power after loss of sources, hydraulic power, air conditioning and pressurisation, ice protection, the ability of the auxiliary power unit to start at altitude where it forms part of the design case.

One duration almost always prevails over the others from below: that of the cargo compartment fire suppression, which is not a capability but a reserve of extinguishing agent. It must cover the longest diversion plus a margin, and it is this duration that, in practice, decides the figure entered in the flight manual. Hence a consequence well known to technical departments: moving from one tier to the next is often a matter of hardware modification — additional bottles, modified flow rate — rather than a paperwork addition.

Endurance capability of significant systems against the diversion time requestedFour vertical bars represent the duration for which each significant system can perform its function. Propulsion and hydraulics are the tallest, electrical power slightly less, cargo compartment fire suppression markedly the lowest. A dashed line placed at the top of the lowest bar marks the ceiling design can approve; a second dashed line, higher up, marks the diversion time requested, out of reach as long as the most limiting system is not modified.endurancetime requestedtype ceilingpropulsionhydraulicselectricalcargo fire
The type’s ceiling is that of the shortest system, not that of the engine. No bar can be exceeded, and it is almost always a consumable duration — the cargo compartment extinguishing agent — that decides the figure entered in the flight manual. Gaining minutes then requires touching the hardware, not the paperwork.

The aircraft’s ability to fly for a long time on one engine depends on two things: how reliable the engines are (measured across all similar aircraft) and how long key systems can keep working. The limiting factor is usually the fire suppression system in the cargo hold, which runs out of extinguishing agent after a certain time. This means that to extend the allowed diversion time, you often need to add more fire extinguishers, not just change the rules.

An Airbus A330-200 with Rolls-Royce Trent 700 engines is approved for 180 minutes of extended diversion time. However, the fire suppression system in the cargo hold can only last 150 minutes before it runs out of extinguishing agent. This means the actual usable diversion time is 150 minutes, not 180, unless the operator modifies the system to carry more agent.

From time to distance: the circle is not where one thinks

The approved value is a time. It becomes a distance only through a convention: a one-engine-inoperative cruise speed, declared by the operator within the approved envelope, in still air and standard atmosphere. The circle drawn around an aerodrome on a planning chart is therefore a calculated object, not a geographic reality.

Two practical consequences follow. The first: the actual wind shifts the equal-time point, sometimes by several tens of nautical miles on a long crossing, and this point is not at the midpoint of the segment. The second, more subtle: the diversion speed used is an operator’s arbitration, not a manufacturer figure. A high speed enlarges the radius and makes the route plannable, but burdens the fuel scenario; a lower speed lightens the fuel and shrinks the circle. Two airlines operating the same type with the same approval may thus be unable to plan the same route.

The diversion flight level adds to this. A depressurisation requires descending, hence flying slowly while burning a great deal, whereas the approved time was converted at an entirely different level. The equal-time point of an engine failure and that of a depressurisation do not coincide, and flight preparation must provide both.

Time to the nearest adequate aerodrome along a crossingRoof-shaped curve: diversion time starts at zero at aerodrome A, rises to a maximum at the midpoint of the crossing, then falls back to zero at aerodrome B. A low dashed line marks the threshold beyond which the extended diversion regime applies; a high dashed line marks the maximum approved diversion time. The portion of curve between the two defines the extended diversion segment, and the gap between the peak of the curve and the high line constitutes the remaining margin.diversion timeroutemaximum approved diversion timethresholdmarginextended diversion segmentaerodrome Aaerodrome B
It is not the route that crosses the threshold, it is the time separating the aircraft from the nearest aerodrome. The curve peaks where the two aerodromes are equidistant; everything above the low line falls under the extended regime, and the gap to the high line measures what remains before the crossing becomes impossible to plan.

What the operator demonstrates in its own right

This is where most of the work lies, and most of the delay. The authority does not ask again to prove that the aircraft flies on one engine: it asks how the organisation will prevent, detect and absorb the failures that the length of the diversion makes intolerable.

Three technicians in blue uniforms inspect a small component under focused light, with a large aircraft engine in the background.
Precision maintenance ensures optimal engine performance during extended operations.

A maintenance programme that forbids the twin fault

The specific risk is not the random failure, it is the common fault of human origin: the same error made the same evening on both engines or on both channels of a redundant system. The dedicated maintenance programme therefore lays down an organisational rule before any technical rule: the same task is not performed on redundant components during the same intervention by the same person, and where this is unavoidable, an independent check is inserted before the flight. To this are added oil consumption and engine parameter trend monitoring, configuration control of installed parts, handling of repetitive defects and a pre-departure check performed by personnel qualified under the extended regime.

A tighter minimum equipment list

The operator’s minimum equipment list carries, for significant systems, conditions specific to the extended regime. An item tolerable for an ordinary flight is no longer so here, or is admitted only at the cost of a reduction in the diversion time authorised for the day. This is the daily tipping point: the aircraft remains technically fit, the route no longer is.

The critical fuel scenario

The calculation has nothing to do with the usual reserves. One takes the most constraining point of the route and accumulates the most penalising circumstances: depressurisation and propulsion failure, descent to a sustainable level, ice accretion on the airframe and operation of engine protections, auxiliary power unit consumption where required, a hold of around a quarter of an hour at low altitude above the aerodrome, approach and landing, all increased by an allowance for wind-forecast error and performance degradation. The result can exceed what the flight itself requires — and it is this fuel, not the circle drawn on the chart, that decides whether the route is feasible that day.

Crews and flight preparation

Training is not limited to handling the failure. It covers the diversion decision itself — when the degradation of a significant system requires turning back while the machine is flying normally — and the particularities of the area: coverage of communication means, low-activity aerodromes, fuel freezing point, survival equipment. Flight documentation must deliver the equal-time points by scenario and the diversion value retained for the day.

Division of demonstrations between the design approval holder and the operator
Object demonstrated Falls to the type Falls to the operator
Propulsion reliability Worldwide fleet in-flight shutdown rate, by airframe-engine combination Observed reliability of its own fleet, reported to the authority
System endurance duration Demonstrated capability of each significant system, margin included Maintenance of this capability through maintenance and the minimum equipment list
Diversion speed and level Envelope approved in the flight manual Values declared and used in the calculations
En-route alternate aerodromes Not applicable Selection, adequacy criteria, weather monitoring
Fuel Certified consumptions Critical scenario and uplift policy
Human competence Not applicable Training, checking, maintenance qualification
Geographic scope None: the capability is indifferent to the route Approved area of operation, route by route

On the day of the flight: three filters below the ceiling

The value that governs the flight is the minimum of four values, read from four separate documents: the design ceiling in the flight manual, the approval in the operations specifications attached to the air operator certificate, the state of the machine in the minimum equipment list, the state of the outside world in the flight file.

The four stages that lower the usable diversion timeFour horizontal bars of decreasing length, stacked from top to bottom, each topped by its label. The first, the longest, represents the capability approved at type level. The second, shorter, represents the approval granted to the operator for a given area. The third takes account of items deferred under the minimum equipment list. The fourth, the shortest, represents what remains usable on the day of the flight once aerodromes, weather and fuel have been taken into account.approved capability of the typeoperator’s approval, by areaaccounting for deferred itemsusable on the day of the flighteach stage can only lower the previous one, never raise it
Four different numbers carry the same name. The one in the flight manual is a design ceiling, the one in the operations specifications an area permission, the one in the minimum equipment list the state of the machine that morning — and only the last one actually authorises the route.

The last filter rests on a distinction everyday language erases. An adequate aerodrome is an almost permanent property: runway, aids, services and rescue and fire-fighting level suit the type. A usable aerodrome is an instantaneous property: this adequate aerodrome is, in addition, announced as operational throughout the whole possible arrival window, planning minima increases included. A list of adequate aerodromes is held; planning is done only with those that are usable, and the window to be covered widens with the diversion time.

Adequate aerodrome and usable aerodrome: two qualifications not checked at the same moment
Criterion Adequate Usable
Nature of the qualification Permanent, established in advance Instantaneous, reassessed for each flight
Elements examined Runway and landing performance, aids, services, rescue and fire-fighting Forecasts and observations, surface condition, actual availability of means
Moment of verification On entry in the operations manual, then periodically At flight preparation, then in flight
Effect of a shortfall The aerodrome comes off the list The route changes, or the flight does not depart
Often overlooked point Fire-fighting level obtained on notice Width of the time window to be covered

The trap: an item deferred under the minimum equipment list lowers the diversion time authorised for the day, whereas the flight plan was calculated the day before on the full value. Nothing flags this at the briefing: the value shown on the file remains that of the approval, the aircraft presents itself fit to depart, and it is a segment of the crossing that ends up outside the circle actually applicable. The same mechanism plays out with an aerodrome that has become unusable after the file was issued.

The right reflex: before accepting the file, reconcile three values rather than one — the one the operations specifications grant for the area, the one the aircraft’s technical state leaves standing, and the one the flight-plan computer actually used. Check along the way the diversion speed and level retained by the fuel scenario: the same number of minutes, served by two different speed assumptions, does not describe the same aircraft.

An agreement that is maintained, and that can be withdrawn

The approval is not a one-off act but a surveillance regime. The operator collects and transmits events that shake the assumptions: in-flight shutdowns, unscheduled engine removals, failures of significant systems, diversions actually carried out and their causes. The authority reads these series as a measure of the continued validity of the approval, not as an administrative report.

The mechanism works both ways. Reliability that degrades at the worldwide level can restrict a tier for all operators of the type; a series of events specific to one fleet restricts only that one. Conversely, it is this accumulation of data that has made it possible to open the longest tiers. The corollary is not comfortable: an operator that produces poor data loses the very instrument that would let it demonstrate it deserves better.

What to go and check in your documentation

Three checks can be done in half a day and avoid months of misunderstanding. The first: identify the document carrying the design capability of your aircraft, with the exact engine variant, and compare it with the approval entered in your operations specifications. The gap between the two is frequent and perfectly normal; what is not normal is to ignore it. The second: find the declared diversion speed and level, and check that they are indeed the ones the planning system uses. The third: list the minimum equipment list items that reduce the diversion time without prohibiting it, because these are the ones that will produce the surprises.

Grey areas remain that documentation handles poorly. An aircraft taken on lease with a different engine variant does not inherit the fleet’s tier. A route crossing several areas of operation may fall under two successive tiers, with the lower one governing its segment. Requirements linked to polar or very cold regions — survival equipment, passenger recovery, freezing point — overlay the extended regime instead of merging with it, and are all the more easily forgotten because they change no number of minutes.

For anyone preparing a type rating or instructing the addition of the capability to an operator certificate, the lesson holds in one sentence: the critical path never runs through the aircraft. This is indeed what an examiner checks when asking, seemingly innocently, which value applies today — and why. The courses at formations.fl330.com address this architecture of approvals before the procedures, because the reverse order produces nothing but rote learning.

This article sets out mechanisms; it replaces no source. The applicable text, the aircraft’s approved flight manual and the operator’s approved documentation prevail over everything above, and it is the version of these documents in force that governs.

Questions fréquentes

Does an aircraft certified for one hundred and eighty minutes authorise the airline to fly at one hundred and eighty minutes?

No. Certification sets a ceiling attached to the airframe-engine combination, recorded in the approved flight manual. Operating at that tier requires a separate approval, granted to the operator for a given area, after demonstrating its dedicated maintenance programme, its minimum equipment list, its critical fuel scenario and its crew training. The approval may remain durably below the type’s capability.

Why does cargo compartment fire suppression so often limit the approved tier?

Because it is not a capability but a consumable reserve: a quantity of extinguishing agent and a flow rate, hence a finite duration. This duration must cover the longest diversion plus a margin, and it is almost always the shortest of the significant systems’ endurance durations. Gaining a tier then requires a hardware modification, not a paperwork addition.

Does the approved diversion time convert into a fixed distance?

No. The conversion is made at a one-engine-inoperative cruise speed declared by the operator, in still air and standard atmosphere. The actual wind shifts the equal-time point along the route, and a descent to low altitude after depressurisation changes both speed and consumption. The circle drawn on a chart is a planning convention, not a geographic boundary.

What is the practical difference between an adequate aerodrome and a usable aerodrome?

Adequacy is an almost permanent property of the aerodrome: runway, landing performance, aids, services and rescue and fire-fighting level compatible with the type. Usability is assessed at the time of the flight: the adequate aerodrome must additionally be announced as operational throughout the whole possible arrival window, with planning minima increases. Planning is done with usable aerodromes, selected among adequate ones.

Can a deferred item remove the benefit of the tier for the day?

Yes, and it is the most common case. The minimum equipment list carries, for significant systems, conditions specific to the extended regime: an item tolerable for an ordinary flight may be prohibited here, or admitted only at the cost of a reduction in the authorised diversion time. The flight plan calculated the day before on the full value then becomes wrong, with no signal of this at the briefing.

Are aircraft with more than two engines covered by this regime?

Yes. The regime has been extended beyond twin-engine aircraft, with a higher threshold that accounts for the propulsion margin remaining after an engine failure. The requirements relating to significant systems, en-route alternate aerodromes and critical fuel apply according to the same logic, propulsion simply ceasing to be the sizing factor in favour of the endurance durations of the other systems.

Commentaires

Leave a Reply

Découvrez l’écosystème FL330

FL330, c’est toute l’aviation professionnelle — explorez nos autres espaces.