Aviation glossary

607 terms

A

  • Accelerate-altitude (A/A)The accelerate-altitude (A/A) is the lowest altitude at which a pilot must immediately increase airspeed if an engine…
  • accelerate-stop distanceThe distance required to accelerate from brake release to V1, then to bring the aeroplane to a full…
  • Accelerate-Stop Distance Available (ASDA)The Accelerate-Stop Distance Available (ASDA) is the maximum length of runway an aircraft has to either accelerate for…
  • Acceleration height (AHA) Acceleration Height AltitudeAcceleration height (AHA) is the altitude at which a pilot must decide whether to continue the takeoff or…
  • acceleration-rejection distanceThe acceleration-rejection distance is the total runway length required for an aircraft to accelerate to the point of…
  • Acceleration-Stop Distance (ASDA)The Acceleration-Stop Distance (ASDA) is the total runway length required for an aircraft to accelerate to its decision…
  • Acceleration-stop distance available (ASDA)The acceleration-stop distance available (ASDA) is the maximum runway length an aircraft can use to accelerate for takeoff…
  • Advection fogAdvection fog occurs when warm, humid air is pushed by wind over a cooler surface, such as cold…
  • Adverse weather delayAn adverse weather delay occurs when a flight is postponed or canceled due to hazardous meteorological conditions, such…
  • Aerodrome forecast (TAF) Terminal Aerodrome ForecastA TAF (Terminal Aerodrome Forecast) is a concise weather forecast specifically for an airport, covering wind, visibility, cloud…
  • Aerodrome Meteorological Observation Message (METAR)A METAR is a routine weather observation report issued by an airport, providing critical data like wind speed,…
  • Aerodrome Meteorological Observation Report (METAR)A METAR is a routine weather observation issued for an airport, providing critical data like wind speed, visibility,…
  • Aerodrome Meteorological Report (METAR) Meteorological Aerodrome ReportA METAR is a concise, coded weather report issued by airports worldwide, providing real-time meteorological data critical for…
  • Aerodrome Pressure (QNH)Aerodrome Pressure (QNH) is the atmospheric pressure adjusted to sea level, allowing pilots to calibrate their altimeters to…
  • Aerodrome QNH (QNH)The Aerodrome QNH is the barometric pressure at a given airport, corrected to the equivalent value at sea…
  • Aerodrome reference altitudeThe aerodrome reference altitude is the altitude displayed by an altimeter when it is set to the local…
  • Aerodrome Reference Height (ARH)The Aerodrome Reference Height (ARH) is a standardized altitude that serves as a critical reference point for air…
  • Aerodrome Weather Report (METAR)A METAR (Meteorological Aerodrome Report) is a routine weather observation issued for aviation purposes, providing essential meteorological data…
  • Aeronautical Competence Assessment (ACC)The Aeronautical Competence Assessment (ACC) is a mandatory periodic evaluation to verify that aviation professionals—such as pilots and…
  • Aeronautical Competence Check (ACC)The Aeronautical Competence Check (ACC) is a formal assessment to verify that an aviation professional meets the required…
  • Aeronautical Competence Examination (ACC)The Aeronautical Competence Examination (ACC) is a formal assessment designed to verify that aviation personnel—such as pilots, air…
  • Aeronautical Competency Check (ACC)An Aeronautical Competency Check (ACC) is a periodic evaluation required to ensure that pilots and air traffic controllers…
  • Aft cabin doorThe aft cabin door is the rear-most door of an aircraft cabin, typically located at the back of…
  • aileronThe aileron is a hinged flight control surface attached to the trailing edge of an aircraft's wing. When…
  • air operator certificateCertificate issued by the authority certifying that an operator has the organization, personnel, means, and procedures necessary to…
  • Air Traffic Control (ATC)Air Traffic Control (ATC) is a system that ensures the safe, orderly, and efficient movement of aircraft by…
  • Air traffic control sector Air Traffic ControlAn ATC sector is a portion of airspace assigned to a particular air traffic controller or team for…
  • Air Transport Pilot Licence (ATPL)The Air Transport Pilot Licence (ATPL) is the most advanced aviation license, enabling pilots to act as captains…
  • Aircraft Maintenance Manual (AMM) Aircraft Maintenance ManualThe Aircraft Maintenance Manual (AMM) is a detailed document provided by the aircraft manufacturer that outlines all maintenance…
  • Aircraft separationAircraft separation is the controlled spacing between aircraft to ensure safe operations in the air and on the…
  • Aircraft separation minimaAircraft separation minima are the prescribed distances or time intervals that air traffic controllers must maintain between aircraft…
  • aircraft type ratingAn aircraft type rating is a qualification added to a pilot's license that permits them to operate a…
  • airfield elevation (QFE)The airfield elevation (QFE) is the height of the airport's reference point above mean sea level, used to…
  • AirframeThe airframe is the primary load-bearing structure of an aircraft, encompassing the fuselage, wings, tail, and landing gear.…
  • airline slotAn airline slot is a permission granted to an airline to operate a flight at a specific time…
  • Airline slot coordination Airline Slot CoordinationAirline slot coordination (ASC) is a regulatory process that allocates specific takeoff and landing times (slots) to airlines…
  • airline slot portfolioAn airline slot portfolio is a set of allocated takeoff and landing times (slots) at congested airports, which…
  • airline slot tradingAirline slot trading is the practice of exchanging or selling airport slots—precious time windows for takeoffs and landings—between…
  • Airline slot utilizationAirline slot utilization refers to the efficiency with which an airline uses its allocated takeoff and landing slots…
  • airline transport pilot licenceHighest level of pilot license, authorizing its holder to serve as a captain on an aircraft operated in…
  • Airport QNH (QNH)The Airport QNH is a standardized atmospheric pressure value used in aviation, representing the air pressure at sea…
  • Airport reference altitude (QFE)The airport reference altitude (QFE) is the atmospheric pressure measured at the airport's elevation, expressed in millibars (hPa)…
  • Airport reference temperature (TREF) Airport Reference TemperatureThe Airport Reference Temperature (TREF) is the highest daily temperature recorded at an airport, used to calculate aircraft…
  • airport slotAn airport slot is a permission to operate a flight at a specific time, granted by airport coordinators…
  • Airport slot allocationAirport slot allocation is the process of assigning specific time windows for aircraft operations at busy airports to…
  • airport slot bankAn airport slot bank is a marketplace where airlines can trade airport slots—precious time windows for takeoffs and…
  • Airport slot capacityAirport slot capacity refers to the limited number of takeoff and landing slots an airport can accommodate within…
  • airport slot demandAirport slot demand refers to the competition for scheduled takeoff or landing times (slots) at congested airports where…
  • airport slot inventoryAn airport slot inventory is a schedule of available time slots for aircraft operations at congested airports. These…
  • Airport slot managementAirport slot management is a coordinated process that allocates specific time windows (slots) for aircraft operations at congested…
  • Airport slot poolAn airport slot pool is a coordinated system of time allocations for aircraft operations at congested airports, ensuring…
  • Airport slot utilizationAirport slot utilization refers to the efficient use of allocated time slots for aircraft takeoffs and landings at…
  • Airworthiness Assurance Organisation (ACMO)The Airworthiness Assurance Organisation (ACMO) is a designated unit within an airline or maintenance organisation responsible for ensuring…
  • airworthiness continuity management organization (ACMO)The airworthiness continuity management organization (ACMO) is an approved entity responsible for ensuring that an aircraft fleet remains…
  • airworthiness directiveA mandatory instruction issued by the airworthiness authority responsible for a type when an unsafe condition is found…
  • Airworthiness Management Organisation (AMO)The Airworthiness Management Organisation (AMO) is a regulatory or operational entity responsible for overseeing the continued airworthiness of…
  • All-engine climb gradient All-engine climb gradientAll-engine climb gradient (AE) is the minimum climb performance an aircraft must achieve after takeoff, assuming no engine…
  • All-engines climb gradient (GA)The all-engines climb gradient (GA) is the steepest angle an aircraft can sustain in a steady climb when…
  • All-Engines Operating Gradient (AEO)The All-Engines Operating Gradient (AEO) is the minimum climb gradient an aircraft must achieve during takeoff with all…
  • All-engines-operating climb gradient (AEO)The all-engines-operating climb gradient (AEO) is the minimum climb performance an aircraft must achieve with all engines running,…
  • Altimeter setting QNH: pressure setting for altitude above sea level; QFE: pressure setting for altitude above airfieldThe altimeter setting is a pressure value (in hectopascals or inches of mercury) that pilots input into their…
  • Altitude above aerodrome level (QFE)Altitude above aerodrome level (QFE) is a height measurement that tells pilots how far above the runway their…
  • altitude deviationAn altitude deviation occurs when an aircraft exits a cleared altitude level without explicit authorization from air traffic…
  • Altitude hypoxia (hypoxia of altitude)Altitude hypoxia occurs when the body's oxygen supply is reduced due to lower atmospheric pressure at high elevations.…
  • anti-icing fluid holdover timeThe anti-icing fluid holdover time is the duration during which a deicing or anti-icing fluid remains effective in…
  • Anti-icing Protection Time (DHT)The Anti-icing Protection Time (DHT) refers to the duration an aircraft can operate without additional deicing after receiving…
  • Approach banAn approach ban is a temporary or permanent restriction prohibiting aircraft from initiating an approach or landing at…
  • Approval Limit (AL)The Approval Limit (AL) is the maximum distance an aircraft can safely start its takeoff roll or land,…
  • Approved Maintenance Organization (AMO)The Approved Maintenance Organization (AMO) is a certification granted under European aviation regulations to companies that meet strict…
  • Area Navigation Required Navigation AreaArea Navigation (RNAV) is a method of aircraft navigation that allows pilots to fly along a desired path…
  • ATC air traffic controlAir traffic control is the service provided by licensed controllers to prevent collisions between aircraft, and on the…
  • Atmospheric discharge (P-static)Atmospheric discharge, also called P-static, is a buildup of static electricity on an aircraft's surface that can create…
  • Atmospheric discharges (P-static)Atmospheric discharges, also called P-static, are static electricity buildups that occur on an aircraft's surface, especially in flight.…
  • Atmospheric fulgurance (P-static)Atmospheric fulgurance, also known as P-static, is the accumulation of static electricity on an aircraft's surface due to…
  • Atmospheric fulguration (P-static)Atmospheric fulguration, also called P-static, is a sudden electrical discharge caused by static buildup on an aircraft's surface.…
  • Atmospheric instabilityAtmospheric instability describes a state where air parcels tend to rise or sink rapidly, leading to turbulent or…
  • Atmospheric pressureAtmospheric pressure is the force exerted by the weight of air molecules in the Earth's atmosphere. It decreases…
  • Atmospheric static discharge (P-static)Atmospheric static discharge, often called P-static, is a sudden release of built-up static electricity in the air around…
  • authorization limitThe authorization limit is a boundary beyond which an aircraft is not permitted to proceed without explicit clearance…
  • Automatic Dependent Surveillance-Broadcast (ADS-B) Automatic Dependent Surveillance-BroadcastADS-B is a modern air traffic surveillance technology where aircraft equipped with GPS and a transmitter broadcast their…
  • Automatic terminal information service Automatic Terminal Information ServiceThe Automatic Terminal Information Service (ATIS) is a pre-recorded broadcast providing pilots with critical details about an airport,…
  • auxiliary power unitAn auxiliary power unit (APU), typically located in the tail cone, provides electrical power and bleed air independently…
  • Available Takeoff Distance to Stop (ASDA)The Available Takeoff Distance to Stop (ASDA) is the maximum length of runway required for an aircraft to…
  • Aviation professionals: Operations, Maintenance, Cabin Crew, Air Traffic Control, Aviation Safety, Career PathsThis glossary entry provides an overview of the core domains in aviation, including flight operations, aircraft maintenance, cabin…

B

  • balanced field lengthThe take-off field length obtained when the accelerate-stop distance and the accelerate-go distance are made equal, at the…
  • balanced runway lengthThe balanced runway length is the critical length required to ensure that an aircraft can either take off…
  • base maintenanceMaintenance whose extent requires the aircraft to be taken out of service for a substantial period: heavy structural…
  • Bleed airBleed air is compressed air extracted from the engine compressor section of a gas turbine. It is used…
  • Bleed valveA bleed valve is a component in turbine engines that diverts high-pressure air from the compressor section to…
  • Borescope inspectionBorescope inspection is a non-destructive method used to examine the internal components of an aircraft engine, such as…
  • bulkheadA bulkhead is a solid partition or wall inside an aircraft that divides the cabin into distinct sections,…

C

  • Cabin altitudeCabin altitude refers to the simulated altitude at which the air pressure inside an aircraft is maintained, typically…
  • cabin crew attestationThe document issued under Part-CC certifying that its holder has completed the initial cabin safety training course and…
  • Cabin Crew Certificate (CCC)A Cabin Crew Certificate (CCC) is an official document confirming that flight attendants have completed the necessary training…
  • Cabin crew coordination (CCC) Cabin Crew CoordinationCabin crew coordination (CCC) refers to the structured cooperation and communication among flight attendants to manage safety, emergencies,…
  • cabin depressurizationCabin depressurization occurs when the air pressure inside an aircraft's cabin falls below the standard level required for…
  • Cabin Equipment Certificate (CEC)The Cabin Equipment Certificate (CEC) is an official document issued by aviation authorities to verify that a commercial…
  • Cabin pressure (CP) Cabin PressureCabin pressure (CP) is the controlled air pressure inside an aircraft cabin, maintained at a level higher than…
  • Cabin pressure control system (CPCS) Cabin Pressure Control SystemThe cabin pressure control system (CPCS) regulates the air pressure inside an aircraft to ensure passenger and crew…
  • cabin pressure lossA cabin pressure loss occurs when the aircraft's pressurization system fails, causing a rapid decrease in air pressure…
  • Cabin SecureCabin Secure is a formal announcement made by the cabin crew to the flight deck, indicating that all…
  • cargo manifestA cargo manifest is a formal document that records all items loaded onto an aircraft, from passengers and…
  • CeilingThe ceiling in aviation refers to the lowest altitude of the base of a cloud layer that covers…
  • center of gravity (CG)The center of gravity (CG) is the point where an aircraft’s total weight is considered to be concentrated.It’s…
  • centre of gravityThe centre of gravity is the point at which the aircraft's mass may be taken to act, and…
  • Certificate of Crew Competence (CCA)The Certificate of Crew Competence (CCA) is an official document issued to aviation personnel, confirming they have successfully…
  • Certificate of Crew Competence Achievement (CCA)A Certificate of Crew Competence Achievement (CCA) is an official document issued to flight crews after they have…
  • Certificate of Crew Competency (CCC)The Certificate of Crew Competency (CCC) is an official document issued to aircrew members, confirming they meet the…
  • certificate of release to serviceThe signed statement issued after maintenance certifying that the work was carried out in accordance with approved data…
  • circling approachThe visual phase that extends an instrument approach when the final approach track cannot be aligned with the…
  • circuit (CIRCLING)A circuit, or circling approach, is a standard procedure used when a direct straight-in approach to the runway…
  • circular approachA circular approach is a procedure where a pilot visually aligns with a runway that is not directly…
  • class 1 medical certificateThe medical fitness certificate required to exercise the privileges of a professional pilot licence (CPL, MPL, ATPL). It…
  • Class-1 Aviation Medical CertificateA Class-1 Aviation Medical Certificate is a mandatory medical assessment issued by an aviation medical examiner to ensure…
  • Clear-air turbulence (CAT) Clear Air TurbulenceClear-air turbulence (CAT) is a type of atmospheric turbulence that occurs in cloudless regions of the sky, making…
  • clearance limitThe clearance limit is a specific geographical boundary or waypoint assigned by air traffic control (ATC) that defines…
  • clearance void time clearance void timeA clearance void time (CVT) is a specified duration after which an air traffic control (ATC) clearance expires…
  • Climb gradientClimb gradient is the ratio of altitude gain to horizontal distance traveled, typically expressed as a percentage or…
  • Climb gradient all engines (GA)This is the rate at which an aircraft can gain altitude when all its engines are operating normally,…
  • Climb gradient at full power (GA)The climb gradient at full power (GA) is the minimum slope an aircraft must achieve during ascent with…
  • Climb gradient with full power (GA)The climb gradient with full power (GA) is the minimum slope an aircraft must achieve during takeoff or…
  • Climb gradient with full thrust (GA)The climb gradient with full thrust (GA) is the steepest steady climb angle an aircraft can achieve when…
  • Climb performance at full thrust (TOGA)Climb performance at full thrust (TOGA) refers to the rate at which an aircraft can ascend when all…
  • Climb performance with all engines (ETOPS)Climb performance with all engines refers to an aircraft's ability to ascend after takeoff when all powerplants are…
  • climb performance with all engines operating (TOGA)Climb performance with all engines operating (TOGA) refers to an aircraft's ability to ascend efficiently when all its…
  • Collision Avoidance Recommendation (RA)The Collision Avoidance Recommendation (RA) is a critical safety feature in modern aircraft, generated by systems like TCAS…
  • Collision Avoidance Resolution Advisory (RA)A Collision Avoidance Resolution Advisory (RA) is an automated warning issued by the Traffic Alert and Collision Avoidance…
  • Collision Avoidance Resolution Alert (RA)The Collision Avoidance Resolution Alert (RA) is a critical feature of the Traffic Alert and Collision Avoidance System…
  • Collision Avoidance Warning (RA)The Collision Avoidance Warning (RA) is a component of the Traffic Alert and Collision Avoidance System (TCAS), which…
  • commercial pilot licenceLicense that authorizes remunerated work as a pilot: captain of an aircraft operated with a single pilot in…
  • Compressor stallA compressor stall occurs when the airflow through a jet engine's compressor section becomes disrupted, leading to a…
  • Compressor surgeCompressor surge is a disruptive airflow phenomenon in jet engines where the compressor's blades stall, causing a rapid…
  • configuration deviation listThe approved list, published in the aircraft flight manual by the type certificate holder, of secondary airframe parts…
  • contaminated runwayA runway of which more than 25 % of the surface area required for the operation is covered…
  • Continuing AirworthinessContinuing airworthiness refers to the ongoing maintenance, inspections, and compliance checks required to ensure an aircraft remains safe…
  • continuing airworthiness management organisationApproved organization responsible for managing the continued airworthiness of a fleet: developing and revising the maintenance program, applying…
  • continuity of airworthiness management organization (CAMO)The CAMO is a specialized organization responsible for maintaining an aircraft's airworthiness throughout its operational life, even as…
  • control column (or control wheel)The control column, also called the control wheel in some aircraft, is the primary input device for the…
  • control stickThe control stick is a primary flight control input device in an aircraft, typically used to adjust the…
  • control surfaceA control surface is a hinged or movable aerodynamic surface on an aircraft, such as an aileron, elevator,…
  • control wheelThe control wheel is a primary flight control input device used in most aircraft to control the ailerons…
  • control yoke (or control column)The control yoke is the primary flight control input device in most fixed-wing aircraft, resembling a steering wheel…
  • Controller-pilot data link communications (CPDLC) Controller-pilot data link communicationsCPDLC is a text-based communication system that allows air traffic controllers and pilots to exchange messages digitally, reducing…
  • Convective activityConvective activity refers to the vertical movement of air due to heating, leading to the formation of cumulus…
  • Convergence Point System (MPS)The Convergence Point System (MPS) is a traffic management tool used to coordinate multiple aircraft toward a single,…
  • Crew AttestationA Crew Attestation is an official certificate confirming that cabin crew members have undergone mandatory training and comply…
  • Crew Cabin Attestation (CCA)The Crew Cabin Attestation (CCA) is a formal document used in aviation to certify that the flight crew…
  • Crew Certificate of Attainment (CCA)The Crew Certificate of Attainment (CCA) is an official document issued to flight attendants after they successfully complete…
  • Crew Competency Certificate (CCC)The Crew Competency Certificate (CCC) is an official document issued to flight crews after they have successfully completed…
  • Crew Declaration (CCA)The Crew Declaration (CCA) is a standardized document used in aviation where flight crew members declare their fitness…
  • crew resource managementA set of non-technical skills through which a crew leverages all available resources—people, equipment, information—to conduct a flight…
  • Crew Rest Area (CRA)The Crew Rest Area (CRA) is a designated compartment in commercial aircraft, typically located in the upper deck…
  • Crew Rest Compartment (CRC) Crew Rest CompartmentThe Crew Rest Compartment (CRC) is a designated, enclosed space in commercial aircraft designed to provide flight crew…
  • Crew Rest FacilityA Crew Rest Facility (CRF) is a designated area on a commercial aircraft, typically located in the cabin…
  • Critical engineA critical engine is the engine whose failure would most severely impact an aircraft's performance, typically the outboard…
  • critical phaseA critical phase is a predefined time window during which a specific flight operation must be executed to…
  • critical timeThe critical time is the precise point in a flight operation where a decision must be made to…
  • CrosswindA crosswind is a wind that blows perpendicular or at an angle to an aircraft's flight path, particularly…
  • crosswind componentThe crosswind component is the portion of the wind that is perpendicular to the runway's centerline, affecting an…
  • Crosswind landingA crosswind landing occurs when an aircraft touches down with a significant wind component blowing perpendicular to the…
  • currency (flight experience)Currency refers to the requirement that pilots maintain a minimum level of recent flying experience to ensure their…
  • current experience (flight)Current experience refers to the minimum flight activity a pilot must maintain to stay proficient on a particular…
  • current flight experienceCurrent flight experience refers to the ongoing practice of flying that pilots undertake to keep their skills up…

D

  • damage toleranceDamage tolerance refers to the ability of an aircraft structure to withstand and contain damage without catastrophic failure…
  • dangerous goodsDangerous goods are articles or substances capable of posing a risk to health, safety, property or the environment…
  • de-icing holdover timeDe-icing holdover time, on the ramp simply holdover time, is the estimated period during which an anti-icing fluid…
  • decision altitudeDecision altitude is the point in an instrument approach where the pilot must see the runway environment or…
  • decision heightThe decision height is the height, referenced to the elevation of the runway threshold, at which a missed…
  • decision point (MAP)The decision point (MAP) is a critical waypoint in an instrument approach procedure where the pilot must assess…
  • Decision Speed (V1)The Decision Speed (V1) is the critical speed during takeoff where the pilot must choose between continuing the…
  • Decision speed for takeoff (V1)The decision speed for takeoff (V1) is a critical speed in aviation determined during performance calculations. It marks…
  • DecompressionDecompression is a rapid drop in cabin pressure, often caused by a structural failure like a window or…
  • deferred defectA deferred defect is a non-critical technical problem that does not pose an immediate safety risk but requires…
  • deicing fluid holdover time (HOT)The deicing fluid holdover time (HOT) is the duration a deicing fluid remains effective after application, preventing ice…
  • Deicing holdover time (DHT)The deicing holdover time (DHT) is the period during which an aircraft's surfaces remain free of ice after…
  • dependent onIn aviation, when a system, procedure, or outcome is dependent on a specific condition, it means its behavior…
  • Derated takeoffA derated takeoff is a procedure where an aircraft’s engine(s) are intentionally operated at less than their maximum…
  • Designated Maintenance Organisation (DMO) Designated Maintenance OrganisationA Designated Maintenance Organisation (DMO) is an entity officially authorised by aviation authorities to carry out maintenance, repairs,…
  • Dew PointThe dew point is the temperature at which air can no longer hold all its water vapor, causing…
  • Direct controller-pilot communications (DCL) Direct Controller-Pilot CommunicationsDirect controller-pilot communications (DCL) is a method of radio communication where air traffic controllers and pilots exchange messages…
  • Distance Measuring Equipment (DME) Distance Measuring EquipmentDistance Measuring Equipment (DME) is a ground-based radio navigation aid that measures the slant-range distance between an aircraft…
  • Dry adiabatic lapse rateThe dry adiabatic lapse rate (DALR) is the rate at which a parcel of dry air cools as…
  • Dry iceDry ice is the solid form of carbon dioxide (CO₂) that sublimates (turns directly from solid to gas)…
  • duty periodA duty period is the total time a flight attendant is required to be available for work, from…

E

  • EASA European Union Aviation Safety AgencyEASA is the agency of the European Union responsible for drafting aviation rules, certifying aeronautical products and overseeing…
  • echelon formation (VFR)An echelon formation is a VFR (Visual Flight Rules) flying technique where aircraft are positioned diagonally behind and…
  • Economic load factor Economic Load FactorThe economic load factor (ELF) is a key performance metric in aviation, representing the percentage of available seating…
  • EGT margin Exhaust Gas TemperatureEGT margin (Exhaust Gas Temperature margin) is the difference between the current EGT and the engine's maximum allowable…
  • emergency evacuationEmergency evacuation is the immediate and orderly departure of all occupants from an aircraft using all available exits,…
  • emergency exitAn emergency exit is a specially designed door or opening in an aircraft that allows for rapid evacuation…
  • Emergency landing and evacuationAn emergency landing and evacuation occurs when an aircraft is forced to land unexpectedly, often due to mechanical…
  • Emergency Operations Procedure (EOP)The Emergency Operations Procedure (EOP) is a standardized checklist pilots use when an engine fails during flight. It…
  • Emergency procedure for engine failure (EOP)The Emergency procedure for engine failure (EOP) is a structured checklist and set of actions designed to safely…
  • En Route Chart (ENR) En Route ChartAn En Route Chart (ENR) is a detailed map used by pilots to navigate between airports, displaying airways,…
  • en route clearanceAn en route clearance is an air traffic control (ATC) authorization that allows an aircraft to proceed along…
  • en-route airspace holdingEn-route airspace holding is a controlled delay procedure where an aircraft is instructed to remain within a designated…
  • Engine Condition Monitoring (ECM) Engine Condition MonitoringEngine Condition Monitoring (ECM) is a diagnostic system that continuously analyzes an aircraft engine's performance data, such as…
  • Engine Failure Procedure (EOP)An Engine Failure Procedure (EOP) is a standardized checklist that pilots use to safely manage and recover from…
  • Engine Failure Recognition (EFR) Engine Failure RecognitionEngine Failure Recognition (EFR) is the process by which pilots identify and confirm the loss of an engine's…
  • engine fireAn engine fire occurs when an aircraft's powerplant ignites due to overheating, fuel leaks, or electrical faults. It…
  • Engine oil consumption Engine Oil ConsumptionEngine oil consumption (EOC) refers to the gradual loss of lubricating oil from an aircraft engine during operation.…
  • Engine Shutdown Procedure (ESP)The Engine Shutdown Procedure (ESP) is a standardized sequence of actions to deactivate an aircraft engine in a…
  • Engine-Out Clearance Altitude (EOC)The Engine-Out Clearance Altitude (EOC) is the lowest altitude an aircraft must maintain if an engine fails during…
  • Engine-out climb altitude (EOC)The engine-out climb altitude (EOC) is the maximum height an aircraft can gain after an engine failure during…
  • Engine-out climb gradient (OE) Out of EngineThe engine-out climb gradient (OE) is the performance metric that defines how well an airplane can climb after…
  • Engine-out climb obstacle clearance height (EOC)The EOC is a critical safety parameter that defines the minimum height an aircraft must achieve after losing…
  • Engine-Out Climb Performance (EOC)The Engine-Out Climb Performance (EOC) is a critical safety metric that determines the highest altitude an aircraft can…
  • Engine-out obstacle clearance altitude (EOC) Engine-out obstacle clearance altitudeThe engine-out obstacle clearance altitude (EOC) is the lowest safe altitude an aircraft must reach if an engine…
  • Engine-out obstacle clearance height (EOC)The engine-out obstacle clearance height (EOC) is the critical altitude an aircraft must achieve after an engine failure…
  • Engine-out procedure (EOP) engine-out procedureThe engine-out procedure (EOP) is a standardized checklist and sequence of actions pilots use when an aircraft loses…
  • Equipment Competency Certificate (ECC)The Equipment Competency Certificate (ECC) is an official document issued to flight crews after they complete specialized training…
  • European Union Aviation Safety Agency (EASA)The European Union Aviation Safety Agency (EASA) is the regulatory body responsible for ensuring the safety of civil…
  • evacuation slideAn evacuation slide is an inflatable or rigid slide designed to facilitate rapid passenger egress from an aircraft…
  • Exhaust gas temperature (EGT) Exhaust Gas TemperatureExhaust gas temperature (EGT) measures the heat of gases expelled from an aircraft engine, typically in degrees Celsius…
  • exploitation manualThe exploitation manual is a standardized document used by airlines and operators to ensure consistent and safe operations.…
  • extended range operationsExtended range operations, almost always spoken as ETOPS, are operations by two-engined aeroplanes on routes where the flight…
  • Extended-range operation (EROPS)Extended-range operation (EROPS) refers to the practice of operating a twin-engine aircraft beyond the maximum distance from a…
  • Extended-range Twin-engine Operations (ETOPS)Extended-range Twin-engine Operations (ETOPS) is an aviation regulation that permits twin-engine aircraft to fly routes that are beyond…

F

  • Fan blade out (FBO) Fan Blade OutA fan blade out (FBO) occurs when a turbine engine's fan blade fractures or detaches mid-flight, often due…
  • fatigue risk management systemA system by which an operator manages fatigue-related risk using its own data — sleep logs, bio-mathematical models,…
  • field elevation (QFE)Field elevation (QFE) is the height of the airport's terrain above mean sea level (MSL). It is used…
  • Field elevation reference (QFE)The field elevation reference (QFE) is the atmospheric pressure at the airport's elevation, measured at the runway level.…
  • Field length limitation (FLL) Field Length LimitationA field length limitation (FLL) is a performance-based constraint that defines the minimum runway length required for an…
  • final approach fixThe final approach fix is the charted point at which the final approach segment begins and the final…
  • Final Approach Point (FAP)The Final Approach Point (FAP) is a key reference point in aviation, marking the start of the final…
  • Final approach speed V<sub>REF</sub> (Reference Speed for Final Approach)Final approach speed (VREF) is the target speed for an airplane during the final approach to landing, ensuring…
  • fire extinguisherA fire extinguisher is a handheld or mounted device containing a fire-suppressing agent, designed to extinguish small fires…
  • Flap settingFlap setting refers to the angle at which an aircraft's flaps are extended from the wings. Flaps are…
  • flare marginFlare margin is the additional altitude a pilot can safely lose during the flare maneuver before the aircraft…
  • Flex TemperatureFlex temperature is the maximum allowable engine temperature for a given flight phase, optimized to balance fuel efficiency…
  • Flexibility Temperature (Flex)The Flexibility Temperature (Flex) is the minimum ambient temperature at which an aircraft can achieve full takeoff thrust…
  • Flight and duty time limitations (FDTL)Flight and duty time limitations (FDTL) are regulatory rules that define the maximum time a flight crew can…
  • Flight crew licensingFlight crew licensing is a system of regulations and qualifications that ensures pilots and cabin crew meet safety…
  • Flight Data Acquisition (FDA)Flight Data Acquisition (FDA) refers to a system that automatically collects and records key flight parameters, such as…
  • flight data monitoringSystematic use of recorded flight parameters to detect operational deviations before they result in an event. Data is…
  • flight data recording (FDR)Flight data recording (FDR) is a system that continuously captures and stores key flight parameters, such as altitude,…
  • Flight dispatchFlight dispatch is the ground-based function responsible for preparing and monitoring flight plans, ensuring compliance with regulations, and…
  • Flight dispatch release Flight Dispatch ReleaseA flight dispatch release (FDR) is a formal document issued by a flight dispatcher or operations center authorizing…
  • Flight dispatcherA flight dispatcher is a licensed aviation professional who works alongside pilots to plan and monitor flights. They…
  • flight levelA surface of constant atmospheric pressure referenced to the standard datum of 1013.25 hPa (29.92 inHg), separated from…
  • Flight Management System (FMS) Flight Management SystemThe Flight Management System (FMS) is an advanced avionics suite that integrates navigation, performance, and flight planning functions.…
  • Flight OperationFlight Operation refers to the rotational speed (N1 or N2) at which the aircraft's engines are set to…
  • Flight Operations Manual (FOM) Flight Operations ManualThe Flight Operations Manual (FOM) is a comprehensive document outlining the standard operating procedures, policies, and guidelines for…
  • Flight Operations Quality Assurance (FOQA)Flight Operations Quality Assurance (FOQA) is a data-driven program that analyzes recorded flight parameters to identify trends, risks,…
  • Flight Operations Quality Assurance Organization (FOQA)The Flight Operations Quality Assurance Organization (FOQA) is a specialized entity within aviation operations that systematically monitors and…
  • Flight Path Conflict Alert (FPCA)A Flight Path Conflict Alert is an automated collision avoidance instruction that directs a pilot to perform a…
  • Flight Plan (FPL) Flight PlanA flight plan (FPL) is a formal document filed by a pilot or flight dispatcher with air traffic…
  • flight planningFlight planning involves determining the most efficient routes, altitudes, and schedules for an aircraft to follow, considering factors…
  • Flight Proficiency Check (FPC)A Flight Proficiency Check (FPC) is a formal evaluation conducted to ensure a pilot meets the required standards…
  • Flight Safety Examination (ACC)A Flight Safety Examination (ACC) is a formal assessment conducted to verify that pilots, air traffic controllers, or…
  • Flight schedulingFlight scheduling is the systematic planning of flight times, routes, and aircraft assignments to maximize efficiency and minimize…
  • Flight scheduling system (FSS) Flight Scheduling SystemA flight scheduling system (FSS) is a software tool used by airlines to create, optimize, and manage flight…
  • Flight Technical Competence Check (ACC)A Flight Technical Competence Check (ACC) is a periodic evaluation required by aviation authorities to verify that pilots…
  • Flight Technical Competency Check (ACC)A Flight Technical Competency Check (ACC) is a formal assessment conducted at set intervals to verify that pilots…
  • flight time limitationsA set of rules governing flight time, duty time, and rest periods for crew members, aimed at mitigating…
  • flight worthiness management organization (ACMO)The flight worthiness management organization (ACMO) is a specialized team responsible for ensuring that aircraft maintain their airworthy…
  • flow management position (FMP) flow management positionThe flow management position (FMP) is a specialized role within air traffic control (ATC) that coordinates the movement…
  • fluid anti-icing holdover timeThe fluid anti-icing holdover time is the duration a deicing/anti-icing fluid remains effective in preventing ice accumulation on…
  • Freezing drizzleFreezing drizzle is a meteorological phenomenon where supercooled water droplets fall as drizzle and freeze upon contact with…
  • Freezing levelThe freezing level is the altitude in the atmosphere where the temperature reaches 0°C (32°F), marking the boundary…
  • Friction coefficient μ (mu)The friction coefficient (μ) is a dimensionless number that quantifies the resistance between two surfaces in contact, such…
  • Frontal systemA frontal system is a meteorological phenomenon where two air masses with contrasting temperatures and humidity meet, creating…
  • FrostFrost is a deposit of ice crystals that forms on surfaces when the temperature falls below 0°C (32°F)…
  • Fuel control unit Fuel Control UnitA fuel control unit (FCU) is a critical component in aircraft engines that regulates fuel delivery to ensure…
  • Fuel freeze pointThe fuel freeze point is the temperature at which aviation fuel (typically Jet A-1) starts to form wax…
  • Fuel jettisonFuel jettison is the deliberate release of fuel from an aircraft's tanks to reduce weight in an emergency,…
  • Fuel Tank Safety Fuel Tank SafetyFuel Tank Safety (FTS) refers to regulations and best practices designed to minimize the risk of fuel tank…
  • Full-thrust climb gradient (GA)The full-thrust climb gradient (GA) is the minimum slope an aircraft must maintain during ascent with maximum engine…
  • Fully Automatic Landing (FAL) Fully Automatic LandingFully Automatic Landing (FAL) is an advanced avionics system that enables an aircraft to land autonomously, from the…
  • FuselageThe fuselage is the elongated, tubular structure of an airplane that contains the cockpit, passenger or cargo compartments,…

G

  • GalleyA galley is a compact kitchen installed in the cabin of an aircraft, designed to prepare and serve…
  • General Visual Inspection (GVI) General Visual InspectionA General Visual Inspection (GVI) is a routine examination of an aircraft’s exterior and critical systems to ensure…
  • glide pathThe glide path is a critical component of the Instrument Landing System (ILS), providing vertical guidance to pilots…
  • glide slope (GS)The glide slope (GS) is a radio signal component of the Instrument Landing System (ILS) that provides vertical…
  • glidepath (ILS)The glidepath is the vertical angle that an aircraft must maintain during an ILS (Instrument Landing System) approach…
  • glideslopeThe glideslope is the element of an instrument landing system that provides vertical guidance on final approach. A…
  • Global Navigation Satellite System (GNSS) Global Navigation Satellite SystemThe Global Navigation Satellite System (GNSS) is a network of satellites that provides precise positioning and timing data…
  • go-aroundA go-around is a maneuver where the pilot decides to discontinue an approach to landing and instead climbs…
  • Go-around altitude Go-around altitudeA go-around altitude (GA) is the lowest height at which an aircraft can safely initiate a missed approach…
  • Go-Around Decision Point (GADP) Go-Around Decision PointThe Go-Around Decision Point (GADP) is a critical moment in an aircraft's approach phase when the flight crew…
  • go-around pointThe go-around point is a critical decision point during an approach to landing, where the pilot must initiate…
  • go-around procedureA go-around procedure is a standard maneuver used when a pilot decides to abandon a landing attempt and…
  • Gradient of climb with full thrust (GA)The gradient of climb with full thrust (GA) is the minimum climb angle an aircraft must achieve when…
  • ground handling agentA ground handling agent is a firm that provides essential airport services under contract, including passenger boarding, baggage…
  • ground maintenanceGround maintenance refers to the essential servicing and inspections performed on an aircraft while it is on the…
  • ground megaphone (ground megaphone)A ground megaphone is a handheld or shoulder-mounted device designed to project a person's voice over long distances…
  • Ground Proximity Warning System (GPWS) Ground Proximity Warning SystemThe Ground Proximity Warning System (GPWS) is an electronic device that alerts pilots to potential controlled flight into…
  • Ground rollGround roll refers to the distance an aircraft covers on the ground during takeoff (from brake release to…
  • Ground-Based Augmentation System (GBAS) Ground-Based Augmentation SystemA Ground-Based Augmentation System (GBAS) is a satellite-based augmentation system (SBAS) that enhances the precision of GPS signals…
  • Gust frontA gust front is a narrow, fast-moving boundary of cold, gusty wind that forms ahead of a thunderstorm.…

H

  • HailHail consists of solid ice pellets formed within thunderstorms when updrafts carry raindrops into freezing layers of the…
  • Hard TimeHard Time refers to a maintenance practice where aircraft components are replaced or retired based on a predetermined…
  • Hard Time TaskA Hard Time Task is a specific training requirement that must be completed within a defined period to…
  • Height above airfield elevation (QFE)Height above airfield elevation (QFE) is an altitude measurement that references the air pressure at the airfield itself.…
  • Height above engine-out critical (EOC)The height above engine-out critical (EOC) is a critical safety altitude calculated for aircraft during takeoff, ensuring that…
  • Height Above Obstacles in Case of Engine Failure (EOC)The Height Above Obstacles in Case of Engine Failure (EOC) is a critical safety margin that ensures an…
  • height deviationA height deviation occurs when an aircraft unintentionally exceeds its cleared flight level or altitude. This can happen…
  • High-Level Wind Shear (HLWS) High-Level Wind ShearHigh-Level Wind Shear (HLWS) is a rapid and significant change in wind speed or direction at altitudes typically…
  • holdingA holding pattern is a predetermined flight path that an aircraft follows while waiting for clearance to land…
  • Holding in controlled airspaceHolding in controlled airspace is a procedure where an aircraft is instructed to maintain a specific position in…
  • holding in en-route airspaceHolding in en-route airspace is a maneuver where an aircraft flies a racetrack-shaped pattern over a specific point,…
  • holding orbit (holding)A holding orbit is a predefined, looping flight path that an aircraft follows while waiting for clearance to…
  • holding patternA holding pattern is a standardized flight path designed to keep an aircraft in a specific area while…
  • holdover timeHoldover time is the maximum duration an aircraft can remain uncontaminated by ice after undergoing deicing or anti-icing…
  • Holdover Time for Fluid Deicing (HOT)The Holdover Time for Fluid Deicing (HOT) is the critical window during which an aircraft must depart after…
  • Holdover Time for Liquid Deicing (HOT)The Holdover Time (HOT) is the period during which a liquid deicing treatment remains effective before precipitation or…
  • holdover time of deicing fluidThe holdover time of deicing fluid is the period during which the fluid remains effective in preventing ice…
  • holdover time of deicing fluids (HOTH)The holdover time of deicing fluids (HOTH) is the maximum time an aircraft can remain protected from ice…
  • Human Factors Training (HFT) Human Factors TrainingHuman Factors Training (HFT) is a structured program designed to educate aviation professionals on how human behavior, cognition,…
  • HumidityHumidity refers to the concentration of water vapor present in the atmosphere. It is a key factor in…
  • Humidity inversionA humidity inversion occurs when the relative humidity rises with altitude, contrary to the usual decrease. This happens…
  • hydraulic pumpA hydraulic pump is a mechanical device that converts mechanical energy into hydraulic energy by pressurizing and moving…
  • hydraulic systemA hydraulic system is a mechanical system that uses pressurized fluid to transmit force and control movement in…
  • hydroplaningHydroplaning occurs when a landing aircraft's tires lose contact with the runway due to a layer of water,…
  • HypoxiaHypoxia is a condition where the body or a specific part of it is deprived of adequate oxygen…

I

  • ICAO International Civil Aviation OrganizationICAO is the specialised agency of the United Nations created by the Chicago Convention of 1944 and based…
  • ice protection time (IPT)The ice protection time (IPT) is the period during which an aircraft remains free of ice accumulation after…
  • Icing rateIcing rate measures the speed at which ice accumulates on an aircraft’s surfaces, such as wings or engines,…
  • in case ofAn 'in case of' item is a part or system that remains operational only if it passes regular…
  • in serviceIn aviation, an item marked as 'in service' is one that remains operational while awaiting its next mandatory…
  • In-flight icingIn-flight icing occurs when an aircraft encounters supercooled water droplets in clouds or precipitation, which freeze upon contact…
  • in-flight oxygen in-flight oxygenIn-flight oxygen (IFO) refers to the oxygen supply available to passengers and crew members during flight, particularly in…
  • Inertial Navigation System (INS) Inertial Navigation SystemAn Inertial Navigation System (INS) is a self-contained navigation aid that calculates an aircraft's position, orientation, and velocity…
  • Initial AirworthinessInitial airworthiness refers to the state of an aircraft meeting all regulatory and technical requirements to be deemed…
  • Inoperative Item (IO) inoperative itemAn inoperative item (IO) is a system, component, or piece of equipment on an aircraft that is not…
  • Instrument flight rules (IFR) Instrument Flight RulesInstrument Flight Rules (IFR) are a set of regulations and procedures that allow aircraft to operate in conditions…
  • instrument landing systemThe instrument landing system is the ground-based precision approach aid that combines a localizer for lateral guidance, a…
  • Instrument Landing System Glide Slope (GS) Glide SlopeThe Glide Slope (GS) is part of an Instrument Landing System (ILS) that provides vertical guidance to aircraft…
  • Instrument Landing System Localizer Instrument Landing System LocalizerThe Localizer (LOC) is part of the Instrument Landing System (ILS), providing lateral guidance to align an aircraft…
  • Instrument Landing System Marker Beacon Instrument Landing System Marker BeaconThe Instrument Landing System (ILS) Marker Beacon (MB) is a low-power radio transmitter placed along the approach path…
  • instrument ratingAn instrument rating (IR) is a qualification added to a pilot's license that permits them to fly in…
  • International Civil Aviation Organization (ICAO)The International Civil Aviation Organization (ICAO) is a UN agency responsible for developing international standards and regulations for…
  • interrupted approachAn interrupted approach occurs when a pilot, during the final stages of landing, decides to abort the landing…
  • Interstage turbine temperature (ITT) Interstage Turbine TemperatureThe interstage turbine temperature (ITT) measures the heat between the high-pressure and low-pressure turbine sections in a jet…
  • isobarAn isobar is a line on a weather map that links areas with equal atmospheric pressure. It helps…

J

  • Jet pipe temperature Jet Pipe TemperatureJet pipe temperature (JPT) measures the heat of gases exiting a jet engine’s exhaust nozzle. It is a…
  • Jet StreamA jet stream is a narrow, fast-moving air current found in the upper troposphere, typically between 6 and…
  • Just CultureJust Culture is an approach to safety and accountability in high-risk industries, like aviation, where individuals are encouraged…

L

  • Landing distance Landing DistanceLanding distance (LD) is the total length of runway required for an aircraft to land and come to…
  • Landing Distance Available (LDA) Landing Distance AvailableThe Landing Distance Available (LDA) is the total length of runway an aircraft can use for landing, including…
  • Landing Distance Required (LDR) Landing Distance RequiredThe Landing Distance Required (LDR) is the calculated distance an aircraft needs to land and come to a…
  • Landing gear Landing GearThe landing gear (LG) is the undercarriage of an aircraft, typically consisting of wheels, shock absorbers, and supporting…
  • lateral offset procedureA lateral offset procedure is a controlled deviation from the standard flight path where an aircraft is instructed…
  • lavatoryA lavatory is a compact restroom found on commercial aircraft, designed to accommodate passengers and crew during flight.…
  • level bustAn unauthorised vertical deviation from the level an aircraft has been cleared to fly or maintain. It is…
  • licence proficiency checkA practical test conducted by an examiner to revalidate or renew a qualification on a license: type rating,…
  • license proficiency checkA license proficiency check is a mandatory evaluation that pilots must complete periodically to maintain their flying privileges.…
  • life raftA life raft is an emergency flotation device designed to keep passengers and crew safe after an aircraft…
  • lifelineA lifeline is a strong, visible rope installed along the floor of an aircraft to guide passengers during…
  • Lift-induced turbulenceLift-induced turbulence is a type of aerodynamic disturbance generated by the wings of an aircraft as they create…
  • Lift-off distance (LOD) Lift-Off DistanceLift-off distance (LOD) is the horizontal distance an aircraft travels from the start of its takeoff roll until…
  • Lift-off performanceLift-off performance refers to the speed, distance, and conditions required for an aircraft to become airborne during takeoff.…
  • line checkA line check is a formal evaluation conducted in actual flight operations, where a senior pilot or examiner…
  • line formationLine formation is a structured training method where a pilot-in-training flies alongside an experienced instructor on actual commercial…
  • line maintenanceMaintenance carried out on an aircraft in service between flights: transit, daily and weekly checks, servicing and replenishment,…
  • line maintenance release line maintenance releaseA line maintenance release is a formal certification issued by maintenance personnel after completing scheduled inspections or repairs,…
  • Line Release (LR)The Line Release (LR) is a formal authorization issued by maintenance personnel after completing scheduled or unscheduled maintenance…
  • Line Station (LS) Line StationA Line Station (LS) is a designated operational base where an airline manages its daily flight activities, including…
  • line trainingLine training is the phase of pilot training where a trainee, now flying as a co-pilot, performs actual…
  • liquid de-icing holdover timeThe liquid de-icing holdover time is the duration a de-icing fluid remains effective in preventing ice accumulation on…
  • liquid deicing holdover time (LDH)The liquid deicing holdover time (LDH) is the period during which a deicing fluid remains effective in preventing…
  • Load Declaration (Load Sheet)A Load Declaration, often called a Load Sheet, is a critical document in aviation that details the weight…
  • Load factor load factorThe load factor (n) is a ratio that quantifies the aerodynamic forces acting on an aircraft's structure during…
  • load manifestThe load manifest is a critical pre-flight document that records the total weight of passengers, cargo, and fuel,…
  • load sheetThe load sheet is a critical pre-flight document that records the aircraft's actual takeoff weight, fuel load, passenger…
  • localizerThe localizer is the element of an instrument landing system that provides lateral guidance along the extended runway…
  • long-range operations (LRO)Long-range operations (LRO) refer to flights designed to cover exceptionally long distances, often exceeding the typical range of…
  • Low-level wind shear (LLWS) Low-Level Wind ShearLow-level wind shear (LLWS) is a rapid shift in wind speed or direction within a short distance near…
  • Low-visibility proceduresLow-visibility procedures are standardized actions taken at airports to ensure safe operations when visibility is reduced, typically below…

M

  • main gear main gearThe main gear (MG) refers to the main landing gear assembly of an aircraft, typically consisting of two…
  • Main sparThe main spar is the primary structural element of an aircraft wing, providing the necessary strength and rigidity…
  • maintenance baseA maintenance base refers to a facility where heavy maintenance tasks are performed on aircraft, typically involving significant…
  • maintenance release maintenance releaseA maintenance release (MR) is a formal document issued by a maintenance organization certifying that an aircraft has…
  • Mandatory event notificationMandatory event notification refers to the legal requirement for airlines, pilots, and aviation authorities to report specific incidents…
  • Mandatory event reportA mandatory event report is a formal, legally required notification that must be submitted to aviation authorities following…
  • Mandatory incident report (MOR)The Mandatory Incident Report (MOR) is a formal requirement for flight crews to document and submit incidents that…
  • Mandatory Incident Reporting (MOR)The Mandatory Incident Reporting (MOR) is a formal procedure where flight crews document and submit reports of significant…
  • mandatory occurrence reportA mandatory occurrence report is a formal document that aviation professionals must file after certain safety-related incidents or…
  • Mandatory Occurrence Reporting (MOR)The Mandatory Occurrence Reporting (MOR) is a structured process in aviation where flight crews and other personnel are…
  • mandatory report (MOR)A mandatory report (MOR) is an official submission required by aviation authorities after specific incidents, such as near-misses,…
  • Mandatory reporting of an eventAviation regulations require operators, pilots, and other personnel to report specific events, such as accidents, serious incidents, or…
  • Maximum Climb Gradient (GA)The Maximum Climb Gradient (GA) is the minimum slope an aircraft can maintain while climbing at full throttle,…
  • Maximum power climb gradient (GA)The maximum power climb gradient is the minimum climb angle an aircraft can maintain when its engines are…
  • Maximum takeoff weight (MTOW) Maximum Takeoff WeightMaximum takeoff weight (MTOW) is the maximum weight an aircraft is certified to take off under normal operating…
  • Maximum Thrust Climb Gradient (GA)The Maximum Thrust Climb Gradient (GA) is the steepest angle of climb an aircraft can sustain when its…
  • maximum time limitThe maximum time limit is a regulatory constraint that defines the absolute latest point at which a critical…
  • megaphoneA megaphone is a handheld or mounted electronic device that amplifies speech using a built-in microphone and a…
  • Melting Point System (MPS)The Melting Point System (MPS) is a safety feature in aircraft engines that dynamically adjusts thrust to avoid…
  • Merge Point System (MPS)The Merge Point System (MPS) is an air traffic control concept designed to optimize the spacing between aircraft…
  • Merger Point System (MPS)The Merger Point System (MPS) is a traffic management tool used to streamline air traffic by merging multiple…
  • METAR Meteorological Aerodrome ReportA METAR (Meteorological Aerodrome Report) is a routine weather observation issued for aviation purposes, typically every hour or…
  • Meteorological Aerodrome Report (METAR)A METAR is a standardized weather observation report issued by airports worldwide, providing essential meteorological data for aviation…
  • MicroburstA microburst is a localized column of sinking air within a thunderstorm that, upon hitting the ground, spreads…
  • Microwave Landing System (MLS) Microwave Landing SystemThe Microwave Landing System (MLS) is a ground-based navigation aid that provides highly accurate lateral and vertical guidance…
  • Minimum control speed Minimum control speedMinimum control speed (VMC) is the lowest airspeed at which an aircraft can maintain directional control during a…
  • minimum descent altitudeThe lowest altitude, referenced to mean sea level, to which descent is authorised on a non-precision (2D) instrument…
  • minimum equipment listThe operator's document, approved by its authority, listing the equipment that may be unserviceable at dispatch and the…
  • Minimum height in case of engine failure (EOC)The minimum height in case of engine failure (EOC) is the critical altitude at which a pilot must…
  • Minimum Runway Length (MRL) Minimum Runway LengthThe Minimum Runway Length (MRL) is the shortest distance a runway must be to allow an aircraft to…
  • Minimum safe altitude (MSA) Minimum Safe AltitudeThe Minimum Safe Altitude (MSA) is the lowest altitude above ground level that ensures an aircraft can safely…
  • minimum separation (minsep)The minimum separation is a safety buffer enforced between aircraft to prevent collisions in controlled airspace. It can…
  • Missed Approach (Go-Around)A missed approach, also called a go-around, occurs when a pilot determines that landing is unsafe or unfeasible…
  • missed approach pointThe missed approach point is the point on a final approach at which the missed approach must be…
  • Mode S Secondary Surveillance RadarMode S (Secondary Surveillance Radar) is an advanced radar system used in aviation to enhance air traffic control…
  • Moderate icingModerate icing occurs when an aircraft encounters supercooled water droplets in the atmosphere, which freeze on impact with…
  • Mountain wave turbulenceMountain wave turbulence is a type of clear-air turbulence caused by strong winds flowing over mountain ranges, generating…
  • multi-crew pilot licenceLicense introduced by ICAO to train ab initio first officers for multi-crew turbine-powered aircraft, based on a competency-based…
  • multi-crew pilot license (MPL)The multi-crew pilot license (MPL) is an initial pilot certification designed specifically for first officers operating in multi-crew…
  • Multi-Pilot Licence (MPL)The Multi-Pilot Licence (MPL) is a pilot certification designed to prepare pilots specifically for multi-crew operations in commercial…
  • Multi-Pilot License (MPL)The Multi-Pilot License (MPL) is a pilot certification designed to prepare pilots for multi-crew operations in commercial aviation.…

N

  • N1/N2/N3 N1/N2/N3: rotational speeds of different engine spools (low-pressure, high-pressure, intermediate)N1, N2, and N3 refer to the rotational speeds of different sections of a jet engine's compressor and…
  • Non-Compliance Report (NCR) Non-Compliance ReportA Non-Compliance Report (NCR) is a formal document used in aviation to document deviations from regulations, procedures, or…
  • Non-Directional Beacon (NDB) Non-Directional BeaconA Non-Directional Beacon (NDB) is a low-frequency radio transmitter installed at airports or navigational waypoints that emits a…
  • non-radar environmentA non-radar environment is an airspace sector where air traffic control (ATC) relies on procedural separation rather than…
  • Nose gear (NG) Nose GearThe nose gear (NG) is the front landing gear assembly of an aircraft, typically consisting of wheels, struts,…

O

P

  • P-static (precipitation static)P-static, or precipitation static, is a phenomenon where static electricity builds up on an aircraft's surface during flight…
  • PA system (Public Address)A PA (Public Address) system is a network of microphones, amplifiers, and speakers designed to amplify and distribute…
  • Part 145 Organization (or Part 145 Approved Maintenance Organization, AMO)A Part 145 Organization is a maintenance facility authorized by aviation authorities (e.g., FAA, EASA) to perform repairs,…
  • Part 66 Licence (Part 66)A Part 66 Licence is an aviation maintenance certification issued under the European Union's regulatory framework, allowing technicians…
  • Part 66 LicenseA Part 66 License is an official certification issued by aviation authorities, such as EASA or FAA, to…
  • Part-145Part-145 is a European Aviation Safety Agency (EASA) regulation that sets standards for aircraft maintenance organizations (AMOs). It…
  • Part-145 Organisation (AMO)A Part-145 Organisation is a maintenance facility officially approved by aviation authorities like EASA (European Union Aviation Safety…
  • passenger briefing cardA passenger briefing card is a standardized document used by cabin crew to guide passengers through essential safety…
  • Passenger Information System (PA)The Passenger Information System (PA) is an airport or airline tool that provides passengers with live updates on…
  • Performance Class (PC) Performance ClassA Performance Class (PC) is a classification system that categorizes aircraft based on their speed, climb performance, and…
  • performance-based navigationFramework that defines the performance of navigation required on a route, a procedure, or within an airspace volume,…
  • pilot flying under supervision (PFUS)The pilot flying under supervision (PFUS) is the designated pilot at the controls, but the captain remains the…
  • pilot in command under supervisionA co-pilot who performs, on a given sector, all the duties and functions of the commander while the…
  • pitch controlPitch control refers to the ability of an aircraft to adjust its nose-up or nose-down attitude, primarily through…
  • Point Merge System (PMS) Point Merge SystemThe Point Merge System (PMS) is an air traffic control technique designed to streamline aircraft arrivals by merging…
  • portable megaphoneA portable megaphone is a compact, battery-powered device designed to amplify the user's voice for long-distance communication in…
  • power back (go-around)A go-around, or power back, is a maneuver where an aircraft, having initiated its final approach to land,…
  • Power lever angle Power Lever AngleThe power lever angle (PLA) is the measurable position of an aircraft's throttle lever, which determines the fuel…
  • Pre-departure safety briefingA pre-departure safety briefing is a mandatory discussion held by the flight crew before takeoff to review potential…
  • pre-flight safety briefingA pre-flight safety briefing is a mandatory discussion held by the flight crew before each flight to review…
  • Pre-safety briefingThe pre-safety briefing is a mandatory passenger safety briefing conducted before takeoff, covering essential information such as seatbelt…
  • Pre-Takeoff Safety Announcement (PTOSA)The Pre-Takeoff Safety Announcement (PTOSA) is a required verbal briefing by the flight crew to inform passengers about…
  • PrecipitationPrecipitation refers to any form of water—liquid or solid—that falls from the atmosphere to the Earth's surface. It…
  • Precipitation static (P-static) precipitation staticPrecipitation static (P-static) is a form of radio interference caused by static electricity discharging from an aircraft's surface.…
  • Preflight Safety Briefing (PFSB)A Preflight Safety Briefing (PFSB) is a mandatory crew meeting held before every flight to review critical safety…
  • proficiency check (PC)A proficiency check (PC) is a formal evaluation conducted by an examiner to assess whether a pilot or…
  • public address system public address systemA public address system (PAS) is an onboard communication tool that allows crew members to broadcast announcements to…

Q

  • QFEQFE is a specific altimeter setting used in aviation to adjust the instrument so that it reads zero…
  • QFE altitude (QFE)The QFE altitude is the elevation displayed by an altimeter when it is calibrated to the current barometric…
  • QNHQNH is a barometric altitude setting used in aviation that adjusts the altimeter to display height above mean…

R

  • radar vectoringRadar vectoring is a method used by air traffic controllers to direct an aircraft by issuing specific headings…
  • Ramp weightRamp weight is the gross weight of an aircraft measured on the ground before departure, including all fuel,…
  • Rapid Decompression (RD)Rapid Decompression (RD) is an abrupt loss of cabin pressure in an aircraft, typically caused by a structural…
  • Rate of climb at full power (GA)The rate of climb at full power (GA) is the maximum vertical speed a general aviation aircraft can…
  • recencyRecency refers to the elapsed time since a pilot performed a particular aviation activity, such as an instrument…
  • recent experience (flight)Recent experience refers to the accumulated flight hours a pilot has completed in a particular aircraft or under…
  • recent flight experienceRecent flight experience refers to the total hours a pilot has flown within a specific, often regulatory, timeframe,…
  • Regulation (EU) 1321/2014 (Part 145)Regulation (EU) 1321/2014 (Part 145) is the European Union's legal framework governing aircraft maintenance organizations (AMOs). It ensures…
  • reinforced cockpit door (RCD)A reinforced cockpit door (RCD) is a security feature designed to withstand forced entry, typically using hardened materials…
  • Rejected Takeoff (RTO) Rejected TakeoffA rejected takeoff (RTO) occurs when an aircraft aborts its takeoff roll after reaching a critical decision speed…
  • release certificateA release certificate is a formal document issued by a maintenance organization or technician, certifying that an aircraft,…
  • release pointThe release point is a critical boundary in aviation where an aircraft transitions from controlled to uncontrolled airspace,…
  • Release to Service (RTS)Release to Service (RTS) is a formal certification that an aircraft, component, or system has been properly repaired…
  • Release to Service Certificate (RTS)The Release to Service Certificate (RTS) is an official document issued after maintenance, repairs, or modifications to confirm…
  • relief pilotA relief pilot is a qualified pilot who takes over flight duties from another pilot during a long-haul…
  • Reportable Event (RE)A reportable event (RE) is a safety-related occurrence in aviation that does not meet the criteria of an…
  • required navigation performanceRequired Navigation Performance (RNP) is a precise navigation specification that demands continuous monitoring and alertness to ensure the…
  • Resolution Advisory (RA)A Resolution Advisory (RA) is an automated alert issued by a Traffic Collision Avoidance System (TCAS) to prevent…
  • resolution alert (RA)A resolution alert (RA) is an automated collision-avoidance system that warns pilots when their aircraft is on a…
  • Return to Service (RTS)Return to Service (RTS) is the formal process that ensures an aircraft or a component is safe and…
  • return to service certificate (RTS)The return to service certificate (RTS) is an official document issued after maintenance, repairs, or modifications to an…
  • Reverse thrust reverse thrustReverse thrust is a technique used to decelerate an aircraft after touchdown by redirecting engine exhaust forward, creating…
  • root cause analysisStructured approach that traces an event or audit finding back to the underlying factors that made it possible,…
  • RudderThe rudder is a primary flight control surface mounted on the vertical stabilizer (tail fin) of an aircraft.…
  • runway condition reportMessage produced by the aerodrome operator describing the surface condition of each third of a runway, using the…
  • Runway slopeRunway slope refers to the gradient of a runway, either upward (positive slope) or downward (negative slope). It…
  • runway visual rangeRunway visual range is the distance over which the pilot of an aircraft on the centre line of…

S

  • Safety Briefing (PFSB)A Safety Briefing (PFSB) is a required pre-flight discussion led by the flight crew to ensure all personnel…
  • safety demonstrationA safety demonstration is a mandatory pre-flight presentation by cabin crew to explain emergency procedures, including seatbelt use,…
  • safety event (ICAO)A safety event, as defined by ICAO, refers to an occurrence or situation that, under slightly different circumstances,…
  • safety management systemThe formal, organisation-wide arrangement by which an operator, maintenance organisation, aerodrome or service provider identifies hazards, assesses and…
  • safety occurrence (ICAO)A safety occurrence is any event in aviation that has the potential to impact safety, regardless of whether…
  • safety performance indicatorQuantitative measure that an operator or authority monitors to assess whether safety levels are maintained: rate of unstable…
  • Safety SpeedThe Safety Speed is the minimum airspeed that must be maintained during the takeoff phase, specifically from the…
  • Satellite-Based Augmentation System (SBAS) Satellite-Based Augmentation SystemAn SBAS is a ground-based system that enhances the accuracy, integrity, and availability of satellite navigation signals, such…
  • secondary radarSecondary radar is an air traffic control tool that identifies and tracks aircraft by interrogating their onboard transponders,…
  • secure cabin (Cabin Secure)A secure cabin is a reinforced section of an aircraft designed to shield occupants from hazards like rapid…
  • secured cabin (Cabin Secure)A secured cabin is a flight deck or cabin area that is physically isolated and locked to prevent…
  • security incident (ICAO)A security incident in aviation refers to a situation where a threat to safety or security was identified…
  • seniority listThe seniority list is a ranked roster of pilots based on their date of employment, which governs their…
  • separation minimaThe smallest vertical, lateral or longitudinal spacing that an air traffic service may allow between two aircraft. Values…
  • separation minimum (Sepmin)The separation minimum (Sepmin) is the regulated minimum distance between aircraft, either in flight or on the ground,…
  • sequencing and meteringSequencing and metering is a key air traffic control (ATC) technique used to manage aircraft arrivals and departures,…
  • service bulletinA service bulletin (SB) is a formal document issued by an aircraft manufacturer to inform operators of recommended…
  • Severe icingSevere icing is an extreme form of atmospheric icing where ice accumulates rapidly on an aircraft's wings, engines,…
  • SkinThe skin of an aircraft is the thin outer layer of material that covers the fuselage, wings, and…
  • smoke hoodA smoke hood is a portable, oxygen-independent breathing apparatus designed for cabin crew during aircraft emergencies, particularly fires…
  • sparA spar is a main structural member of an aircraft wing, typically running spanwise (from root to tip)…
  • special authorizationA special authorization is an official exception granted by aviation authorities to perform an operation that would otherwise…
  • specific approvalA specific approval is a formal authorization granted by aviation authorities to permit an operation that would otherwise…
  • specific authorizationA specific authorization is an exception granted by aviation authorities to perform flight operations that would otherwise be…
  • SquawkThe squawk is a four-digit code assigned by air traffic control (ATC) or selected manually by the pilot…
  • stabilised approachA stabilised approach is a controlled descent phase where the aircraft maintains a consistent speed, flight path, and…
  • stabilized approach (stab app)A stabilized approach is a controlled descent to the runway where the aircraft maintains steady parameters for speed,…
  • Stabilized Approach CriteriaStabilized Approach Criteria are guidelines ensuring an aircraft is correctly aligned, configured, and within safe parameters before landing.…
  • StabilizerA stabilizer is a fixed or adjustable horizontal surface at the rear of an aircraft, working with the…
  • Stall marginA stall margin is the difference between an aircraft's current speed and its stall speed, expressed as a…
  • standard arrival procedure (STAR)A standard arrival procedure (STAR) is a published, preplanned route designed to bring aircraft from a specific point…
  • Standard Arrival Route (STAR)A Standard Arrival Route (STAR) is a published, standardized flight path that pilots follow when descending toward an…
  • standard instrument departureA published IFR route connecting a runway to the en-route structure, defined by tracks, altitude constraints, speed constraints…
  • Standard Terminal Arrival (STAR)A Standard Terminal Arrival (STAR) is a published instrument flight procedure that guides aircraft from a specified enroute…
  • standard terminal arrival procedure (STAR)The standard terminal arrival procedure (STAR) is a predefined, published route for aircraft transitioning from the en-route phase…
  • standard terminal arrival routeA published IFR route linking the en-route structure to a fix from which an instrument approach can begin,…
  • Standardized Aeronautical Meteorology (METAR)A METAR is a standardized format for reporting weather observations at airports. It includes key data like wind…
  • Static discharge (P-static)Static discharge, often called P-static, occurs when accumulated static electricity on an aircraft's surface suddenly releases as a…
  • Static discharges (P-static)Static discharges, also known as P-static, are small electrical sparks that occur around an aircraft in flight due…
  • Static pressureStatic pressure is the atmospheric pressure exerted on an aircraft's surface, independent of its motion. It is measured…
  • sterile cockpitThe sterile cockpit rule is a safety protocol requiring flight crews to avoid non-essential conversations during critical phases…
  • sterile flight deckThe discipline under which no activity or communication unrelated to the safe operation of the aircraft takes place…
  • Stopway EndThe Stopway End is the designated point on an airport runway beyond which an aircraft cannot safely stop…
  • stowage compartmentA stowage compartment is a designated storage space in an aircraft, typically used to hold luggage, emergency equipment,…
  • Structural repairStructural repair involves restoring the integrity of an aircraft's primary components, such as the fuselage, wings, landing gear,…
  • Structural Repair Manual (SRM) Structural Repair ManualA Structural Repair Manual (SRM) is a detailed document that provides approved procedures for repairing structural damage to…
  • subject toIn aviation, 'subject to' refers to a clause or condition that makes an authorization or agreement contingent on…
  • subject to conditionSubject to condition refers to an authorization, clearance, or operation that is only valid if specific criteria are…
  • subject to conditionsThis phrase indicates that a permission or approval is not unconditional but depends on specific criteria being satisfied.…

T

  • TailplaneThe tailplane, also called the horizontal stabilizer, is a fixed or adjustable wing-like surface at the rear of…
  • Takeoff decision speed (V1) Takeoff decision speedV1 is a critical speed during takeoff, calculated based on aircraft performance, runway length, and weight. It marks…
  • Takeoff Performance (TOP) Takeoff PerformanceTakeoff Performance (TOP) refers to the detailed analysis of an aircraft's ability to accelerate, lift off, and climb…
  • takeoff safety speed (V2)Takeoff safety speed (V2) is the minimum speed at which an aircraft can safely climb and maneuver after…
  • Taxiway VisibilityTaxiway visibility refers to the distance at which markings or lights along a taxiway can be clearly seen…
  • Technical Log Technical LogA Technical Log (TL) is a mandatory document where pilots and maintenance crews record any technical problems, defects,…
  • Terrain elevation (QFE)Terrain elevation (QFE) refers to the height of the ground above mean sea level at a specific airport.…
  • Thermal turbulenceThermal turbulence is irregular air movement caused by uneven heating of the Earth's surface, creating rising warm air…
  • threat and error managementThreat and error management (TEM) is a conceptual model used in aviation to describe how pilots and crews…
  • Time LimitIn aviation maintenance, a 'Time Limit' is a predefined threshold (often in flight hours or calendar time) after…
  • time-critical phaseThe time-critical phase refers to a predefined period during which a specific flight operation must be executed to…
  • Touchdown Zone (TDZ) Touchdown ZoneThe Touchdown Zone (TDZ) is the section of a runway where an aircraft is designed to make contact…
  • traffic advisory (TA)A traffic advisory (TA) is a verbal or written alert issued by air traffic control (ATC) to inform…
  • traffic alertA traffic alert is a first-level collision avoidance alert triggered when another aircraft is on a converging path…
  • Traffic Alert and Collision Avoidance System (TCAS)The Traffic Alert and Collision Avoidance System (TCAS) is an airborne device that monitors nearby aircraft and issues…
  • traffic collision avoidance systemAirborne equipment that interrogates the transponders of surrounding aircraft, computes the time to the closest point of approach,…
  • Traffic flow management (TFM) Traffic Flow ManagementTraffic flow management (TFM) is a set of procedures used to regulate the flow of aircraft in the…
  • trail formationTrail formation is an aerial configuration where aircraft fly in a single, straight line, with each aircraft positioned…
  • transition altitudeThe transition altitude is a specific height above ground level (AGL) where aircraft transition between using altimeters set…
  • transponderA transponder is an electronic device that receives a radio signal and automatically transmits a response, typically used…
  • Transponder code (squawk)A transponder code is a unique four-digit identifier transmitted by an aircraft's transponder to ground-based radar systems. It…
  • Trim (T)Trim refers to the fine-tuning of an aircraft's control surfaces (elevators, ailerons, or rudder) to maintain a steady,…
  • Trim adjustmentTrim adjustment refers to the process of fine-tuning the aircraft's control surfaces (e.g., elevators, ailerons, or rudder) to…
  • trim settingThe trim setting refers to the mechanical or electronic adjustment of an aircraft's control surfaces (e.g., elevators, ailerons,…
  • TrimmingTrimming refers to the process of adjusting an aircraft's control surfaces to balance aerodynamic forces, minimizing the pilot's…
  • Turbine inlet temperature (TIT) Turbine Inlet TemperatureThe turbine inlet temperature (TIT) is the highest temperature reached in a gas turbine engine, typically measured just…
  • turnaroundThe turnaround is the critical ground phase between an aircraft's arrival and its next departure. It involves a…
  • Turnaround Time (TAT)Turnaround Time (TAT) is the period between a plane landing and its departure for the next flight. It…
  • Type Certificate Type CertificateA Type Certificate (TC) is a formal document issued by aviation authorities, such as the FAA or EASA,…
  • Type Certificate Holder Type Certificate HolderA Type Certificate Holder (TCH) is an entity, usually an aircraft manufacturer, that has received official approval from…
  • Type RatingA Type Rating is a formal certification that permits a pilot to operate a particular aircraft type. It…
  • type rating instructorThe holder of an instructor certificate issued under Part-FCL that authorises instruction for the issue, revalidation or renewal…

U

  • under conditionAn 'under condition' authorization or operation is one that is only valid when specific criteria or circumstances are…
  • under reservationIn aviation, 'under reservation' indicates that a clearance, approval, or decision is provisional and subject to change based…
  • under reserveAn 'under reserve' part is one that continues to be used in service, but only until the next…

V

  • V1 (decision speed)V1, or decision speed, is a critical speed during aircraft takeoff. It is the point at which the…
  • V2 Takeoff safety speedV2 is a critical speed in aviation, defined as the minimum speed an aircraft must achieve after takeoff…
  • validity (of a qualification)The validity of a qualification refers to the period during which a pilot or crew member is legally…
  • validity periodThe validity period defines the timeframe during which a document, authorization, or data is considered legally or operationally…
  • Variable pitch propeller (VPP) Variable Pitch PropellerA variable pitch propeller (VPP) is a type of propeller where the blades can adjust their angle (pitch)…
  • Very High Frequency Omnidirectional Range (VOR) Very High Frequency Omnidirectional RangeThe VOR is a short-range radio navigation system that provides pilots with accurate bearings to a ground station,…
  • Vibration monitoring (VIB) Vibration monitoringVibration monitoring (VIB) is the continuous or periodic measurement of mechanical vibrations in aircraft engines, propellers, and other…
  • VisibilityVisibility refers to the distance at which objects can be clearly seen, typically measured in meters or statute…
  • Visual flight rules (VFR) Visual Flight RulesVisual flight rules (VFR) are aviation regulations that allow pilots to navigate primarily by visual reference to the…
  • VR rotation speedThe rotation speed: the calibrated airspeed at which the pilot flying begins to raise the nose so that…

W

  • Wake TurbulenceWake turbulence consists of rotating air currents generated by the wings of an aircraft as it moves through…
  • Wake Turbulence Category (WTC) Wake Turbulence CategoryThe Wake Turbulence Category (WTC) is a classification system that assigns aircraft to one of four categories (Light,…
  • WaypointA waypoint is a predefined geographical location used in aviation navigation, typically defined by latitude and longitude coordinates.…
  • Weight and Balance Manual (WBM) Weight and Balance ManualThe Weight and Balance Manual (WBM) is a regulatory document that provides detailed guidelines for calculating and distributing…
  • Wet compressionWet compression occurs when liquid fuel or oil enters an aircraft engine's cylinders during the compression stroke, mixing…
  • wet startA wet start is a type of engine start failure where the engine ignites but fails to accelerate…
  • Wind Correction Angle (WCA) Wind Correction AngleThe Wind Correction Angle (WCA) is the angle a pilot steers into the wind to counteract its effect…
  • Wind gradientThe wind gradient refers to the rate at which wind speed or direction changes with altitude or horizontally…
  • wind shear (WS)Wind shear is a rapid shift in wind velocity or direction over a short distance, either horizontally or…
  • Windmill startA windmill start is a method of restarting an aircraft engine by using the wind to rotate the…
  • windshearWindshear is a rapid and significant shift in wind velocity or direction, either horizontally or vertically. It can…
  • wing boxThe wing box is the primary structural component of an aircraft wing, typically formed by the front and…
  • Wingtip vortex (WT)A wingtip vortex (WT) is a spinning air mass that develops at the wingtips of an aircraft in…

Y

  • Yaw controlYaw control is the system that adjusts an aircraft's movement around its vertical axis, preventing unwanted sideways drift…

Z

  • Zero fuel weight (ZFW) Zero Fuel WeightZero fuel weight (ZFW) is the maximum allowable weight of an aircraft when its fuel tanks are empty,…

Découvrez l’écosystème FL330

FL330, c’est toute l’aviation professionnelle — explorez nos autres espaces.